Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2018.10–2019.09
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372441 ENGINE ASSEMBLY A

M20A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING BRACKET LH (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the engine mounting bracket LH is necessary.


a.
A433182N01
2.26,0.292 2.417,0.49 0.156,0.198 10 true A 2.385,1.802 2.542,2 0.156,0.198 10 true B 0.927,1.875 1.083,2.073 0.156,0.198 10 true C 1.115,0.125 1.271,0.323 0.156,0.198 10 true D 2.854,1.844 3.01,2.042 0.156,0.198 10 true E

Install the engine mounting bracket LH with the 4 bolts.

Torque:
Bolt (A), (B), (C), (D) : 72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 4 bolts in the order of (B), (C), (D) and (A).



b.

Install the bolt (E) to the flexible hose bracket.

Torque:
Bolt (E) : 26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH (for CVT)

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A433181N01
2.25,0.354 2.406,0.552 0.156,0.198 10 true A 2.604,1.896 2.76,2.094 0.156,0.198 10 true B 1.313,0.229 1.469,0.427 0.156,0.198 10 true D 1.083,1.885 1.24,2.083 0.156,0.198 10 true C

Install the engine mounting insulator LH with the 4 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 4 bolts in the order of (B), (C), (D) and (A).



Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A433180N01
1,1.854 1.156,2.052 0.156,0.198 10 true A 2.813,1.458 2.969,1.656 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A433179N01
0.729,1.417 0.885,1.615 0.156,0.198 10 true A 2.76,1.323 2.917,1.521 0.156,0.198 10 true B 2.438,0.375 2.594,0.573 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH with the 2 bolts and nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Attach the clamp.


c.

Connect the No. 2 ground wire to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.
A429129N01
2.99,3.073 3.146,3.271 0.156,0.198 10 true 1 3.188,1.24 3.344,1.438 0.156,0.198 10 true 2

Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Attach the 2 wire harness clamps.


f.
A434214C01
2.177,0.792 2.313,0.448 true 2.063,1.635 2.063,1.01 true 1.969,1.635 2.177,1.813 0.208,0.177 10 true *1 2.229,0.281 2.458,0.448 0.229,0.167 10 true *2
*1 Suction Pipe Sub-assembly
*2 Air Conditioning Tube And Accessory Assembly


Attach the clamps to connect the suction pipe sub-assembly and air conditioning tube and accessory assembly.


g.

Connect the No. 6 water by-pass hose.


h.

Attach the clamp.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 82121 7.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 19315 8.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 32101 9.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 31400 10.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY (for Manual Transaxle)

Hide 13405 11.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 31250 12.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 13.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 14.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 30400 15.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 12311A 19.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 12371A 20.INSTALL REAR ENGINE MOUNTING INSULATOR (for CVT)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.



Hide 12361 21.INSTALL FRONT ENGINE MOUNTING INSULATOR (for CVT)

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 12371A 22.INSTALL REAR ENGINE MOUNTING INSULATOR (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.



Hide 12361 23.INSTALL FRONT ENGINE MOUNTING INSULATOR (for Manual Transaxle)

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.



Hide 45319 26.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 16261G 28.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 11361J 30.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the cylinder block sub-assembly.


Hide 31.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 23825 32.INSTALL FUEL DELIVERY GUARD

a.

Install the fuel delivery guard to the engine mounting bracket RH with the bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17167 35.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25706 36.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)

Hide 25760 37.INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)

Hide 89481B 38.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ GPF)

Hide 39.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform inspection after repair after replacing the engine assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Set the engine assembly with transaxle on an engine lifter.

A457673C02
0,0 0,0 false
V113146

Attachments - -


NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A433102C01
1.979,1.75 2.198,1.75 2.198,1.75 2.396,1.333 true 1.438,1.75 1.208,1.75 1.208,1.75 1.021,1.458 true 1.99,4.563 2.208,4.563 2.208,4.563 2.313,4.313 true 1.438,4.542 1.208,4.542 1.208,4.542 1.073,4.302 true 1.01,0.844 1.167,1.042 0.156,0.198 10 false . 0.354,2.948 0.51,3.146 0.156,0.198 10 true A 3,2.927 3.156,3.125 0.156,0.198 10 true A 1.073,1.063 1.229,1.26 0.156,0.198 10 true B 2.292,0.99 2.448,1.188 0.156,0.198 10 true B 1.5,4.229 1.656,4.427 0.156,0.198 10 true C 1.771,4.24 1.927,4.438 0.156,0.198 10 true C 0.406,4.021 0.563,4.219 0.156,0.198 10 true D 0.438,4.417 0.594,4.615 0.156,0.198 10 true D 2.875,4.042 3.031,4.24 0.156,0.198 10 true D 2.844,4.417 3,4.615 0.156,0.198 10 true D 1.792,1.656 1.948,1.854 0.156,0.198 10 false *1 1.49,1.656 1.646,1.854 0.156,0.198 10 false *2 1.76,4.469 1.979,4.656 0.219,0.188 10 true *3 1.458,4.448 1.656,4.667 0.198,0.219 10 true *4
*1 Front Bumper Extension Sub-assembly LH
*2 Front Bumper Extension Sub-assembly RH
*3 Rear Front Suspension Member Brace LH
*4 Rear Front Suspension Member Brace RH
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly LH and front bumper extension sub-assembly RH to the front frame assembly and vehicle body with the 2 bolts (A), 2 bolts (B) and 4 nuts.

Torque:
Bolt (A) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (B) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Nut : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


d.

Install the rear front suspension member brace LH and rear front suspension member brace RH to the front frame assembly and vehicle body with the 2 bolts (C) and 4 bolts (D).

Torque:
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Bolt (D) : 60 N*m (612 kgf*cm, 44 ft.*lbf)


e.

for Manual Transaxle:

Install the transverse engine engine mounting insulator to the engine mounting bracket LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



f.

for CVT:

Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

While holding the bolt in place, tighten the nut.



g.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 32101A 40.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 31481A 41.CONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)

a.
A433077

Temporarily install the clutch line.


b.

Install the clutch hose with a new clip.


c.

Using a 10 mm union nut wrench, install the bleeder to flexible hose tube to the clutch release bleeder sub-assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the bleeder clutch release tube.

·

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 48069 45.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 46.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 47.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 48.CONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 49.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 50.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51.CONNECT FRONT SPEED SENSOR LH

Hide 52.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 53.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 54.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 55.STAKE FRONT AXLE SHAFT NUT LH

Hide 37110 56.TEMPORARILY INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 37110 57.TIGHTEN PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)

Hide 58.INSPECT AND ADJUST JOINT ANGLE (for 4WD/AWD)

Hide 58152A 59.INSTALL LOWER NO. 1 FRONT FLOOR HEAT INSULATOR (for 4WD/AWD)

Hide 17410 60.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 45220 61.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 16282 62.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the 2 clips to secure it.


Hide 63.CONNECT WIRE HARNESS

a.
A433096

Connect the wire harness to the vehicle body with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the clamp.


c.

for CVT:

Connect the No. 3 engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

for Manual Transaxle:

Connect the No. 3 engine wire to the manual transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


e.

Attach the claw to install the wire harness to the engine room relay block and junction block assembly.


f.

Connect the 5 connectors to the engine room relay block and junction block assembly.


g.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Attach the 3 claws and install the No. 2 relay block cover to the engine room relay block and junction block assembly.


Hide 88711 64.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 65.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 16572D 66.CONNECT NO. 2 RADIATOR HOSE

a.
A433764C01
1.573,3.781 1.042,3.406 true 0.292,2.833 0.604,2.99 0.313,0.156 10 false *a 1.302,2.948 1.615,3.104 0.313,0.156 10 false *b 1.615,3.719 1.927,3.875 0.313,0.156 10 false *c 0.76,2.833 1.073,2.99 0.313,0.156 10 false *d 1.406,3.313 1.719,3.469 0.313,0.156 10 false *e 2.156,4.042 2.469,4.198 0.313,0.156 10 false *f 0.875,1.802 1.135,1.99 0.26,0.188 10 true *a
*a View A
*b 120°
*c Paint Mark
*d Upper Side
*e RH Side
*f 2 to 5 mm (0.0787 to 0.197 in.)


Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 2 radiator hose is securely inserted to the stopper.




b.

Connect the No. 2 radiator hose to the fan with motor assembly with the clamp.


Hide 16571C 67.CONNECT NO. 1 RADIATOR HOSE

a.
A436898C01
1.573,3.719 1.042,3.344 true 0.302,2.719 0.615,2.875 0.313,0.156 10 false *a 1.323,2.99 1.635,3.146 0.313,0.156 10 false *b 1.635,3.625 1.948,3.781 0.313,0.156 10 false *c 0.885,2.833 1.198,2.99 0.313,0.156 10 false *d 0.406,3.448 0.719,3.604 0.313,0.156 10 false *e 2.146,4.104 2.458,4.26 0.313,0.156 10 false *f 0.854,1.313 1.031,1.521 0.177,0.208 10 true *a
*a View A
*b 120°
*c Paint Mark
*d Upper Side
*e RH Side
*f 2 to 7 mm (0.0787 to 0.276 in.)


Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.

NOTICE:
·

Align the direction of the claw on the clip with the paint mark on the hose.

·

Make sure the No. 1 radiator hose is securely inserted to the stopper.




b.

Connect the No. 1 radiator hose to the No. 1 radiator bracket with the clamp.


Hide 23901 68.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly.

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



b.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


Hide 87245 69.CONNECT INLET HEATER WATER HOSE

a.
A403462C02
1.01,0.979 1.438,0.979 false 1.875,0.969 2.302,0.969 false 1.021,1.354 1.448,1.354 false 1.844,1.365 2.281,1.917 2.281,1.917 2.594,1.917 false 0.813,0.885 1.125,1.042 0.313,0.156 10 false *a 0.833,1.271 1.146,1.427 0.313,0.156 10 false *b 2.365,0.896 2.677,1.052 0.313,0.156 10 false *a 2.635,1.844 2.948,2 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusions of the inlet heater water hose connector with the cutouts in the flow shutting valve (water by-pass hose assembly) and securely insert the inlet heater water hose connector to the stopper of the pipe.


b.
A433084C01
0.792,1.24 1.031,1.24 1.031,1.24 1.302,1.51 true 0.594,1.156 0.781,1.385 0.188,0.229 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector are securely connected by pulling on them.


Hide 87246 70.CONNECT OUTLET HEATER HOSE

a.
A403463C02
1.052,1.156 1.573,1.156 false 0.99,0.365 1.219,0.365 1.219,0.365 1.521,0.792 false 0.875,1.063 1.188,1.219 0.313,0.156 10 false *a 0.823,0.281 1.135,0.438 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the protrusion of the No. 2 water by-pass pipe sub-assembly with the cutout in the outlet heater water hose connector and securely insert the outlet heater water hose connector to the stopper of the pipe.


b.
A433085C01
1.594,1.635 1.833,1.948 1.833,1.948 2.031,1.948 true 2.052,1.844 2.365,2.042 0.313,0.198 10 true *a
*a Retainer
V100135

Push
V100136

Push in


Push in the retainer.


c.

Check that the No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector are securely connected by pulling on them.


Hide 44773F 71.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the vacuum pump assembly.


b.

Attach the hose clamp to the vacuum hose.


Hide 23826 72.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve assembly and slide the clip to secure it.


Hide 33820B 73.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.

Connect the 2 transmission control cables with 2 new clips.


b.

Install the 2 new clips.


Hide 33820B 74.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

NOTICE:

Before installing the transmission control cable assembly, check that the shift lever are in N.


a.
C420965C01
0.49,1.448 0.708,1.656 0.219,0.208 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C416210C01
1.615,0.552 1.823,0.25 1.823,0.25 1.99,0.25 true 1.958,1.344 2.25,0.938 2.25,0.938 2.729,0.938 true 1.531,1.813 1.99,1.813 true 2.042,0.146 2.323,0.385 0.281,0.24 10 false *1 2.792,0.813 3.073,1.052 0.281,0.24 10 false *a 1.323,1.708 1.521,1.938 0.198,0.229 10 true *b
*1 Transmission Control Shaft Lever
*a Manual Valve Link Lever Sub-assembly
*b Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



b.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


c.
A433183C01
0.729,2.906 1.042,3.063 0.313,0.156 10 false *a 2.063,2.896 2.375,3.052 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.


Hide 74404B 75.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly with the 3 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


b.

Attach the 4 clamps to the battery clamp sub-assembly.


c.
A429134C02
1.365,0.76 1.479,0.469 1.479,0.469 1.667,0.469 false 1.063,1.01 0.833,0.76 0.833,0.76 0.656,0.76 false 0.76,1.656 0.677,1.396 0.677,1.396 0.5,1.396 false 1.708,0.375 1.927,0.573 0.219,0.198 10 false *1 0.458,0.667 0.656,0.865 0.198,0.198 10 false *2 0.302,1.292 0.49,1.479 0.188,0.188 10 false *3
*1 Engine Room Main Wire
*2 No. 2 Engine Wire
*3 Positive (+) Battery Terminal


Attach the 2 claws and connect the engine room main wire to the No. 2 engine wire.


d.

Connect the engine room main wire and No. 2 engine wire to the positive (+) battery terminal with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Attach the 2 clamps and connect the engine room main wire and No. 2 engine wire to the battery clamp sub-assembly.


Hide 78.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 17750A 79.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 80.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Attach the 3 clips to install the No. 1 engine cover sub-assembly.


Hide 81.INSPECT VACUUM HOSES (for CVT)

a.

Check that the vacuum hose is installed as shown in the illustration.

A433175C01
0.083,0.052 0.396,0.25 0.313,0.198 10 false *A
*A for 2WD - -


A433176C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *A
*A for 4WD/AWD - -



Hide 82.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 83.INSPECT SHIFT LEVER POSITION

Hide 85.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 89.ADD TRANSFER OIL (for 4WD/AWD)

Hide 90.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 93.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 95.INSPECT FOR ENGINE OIL LEAK

Hide 101.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 52618 102.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Attach the 2 claws to install the front lower bumper absorber.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53737D 104.INSTALL FRONT FENDER APRON SEAL LH

a.
A434185C02
2.719,1.354 2.875,1.552 0.156,0.198 10 false .
V100135

Bolt
V100136

Clip


Install the front fender apron seal LH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736E 105.INSTALL FRONT FENDER APRON SEAL RH

a.
A434186C02
2.99,1.042 3.146,1.24 0.156,0.198 10 false .
V100135

Bolt
V100136

Clip


Install the front fender apron seal RH with the 2 bolts and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58398F 106.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58399D 107.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 58165C 108.INSTALL FRONT FLOOR COVER RH (w/ Cover)

Hide 58166A 109.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 51420 110.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A433068C01
0,0 0,0 false
V100135

Screw
V100136

Bolt


Install the No. 2 engine under cover assembly with the 2 bolts, 2 screws and 6 clips.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 111.INSTALL NO. 1 ENGINE UNDER COVER

a.

Attach the guide to install the No. 1 engine under cover.

A434182C02
5.229,2.302 5.542,2.51 0.313,0.208 10 false .
V100135

Bolt
V100136

Screw



b.

Install the 2 bolts and 10 screws.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53896B 112.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

a.
A434180

Attach the clip to install the front fender front splash shield LH.


b.

Install the 3 screws.


Hide 53895B 113.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

a.
A434181

Attach the clip to install the front fender front splash shield RH.


b.

Install the 3 screws.


Hide 115. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 116.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT