Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM (for A25A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371962 STOP AND START SYSTEM(for A25A-FKS) C

STOP AND START  STOP AND START SYSTEM(for A25A-FKS)  P253014  Ignition Switch Circuit Short to Ground or Open  


DESCRIPTION

If the engine stop and start ECU receives the off signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU will output DTC P253014.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P253014 Ignition Switch Circuit Short to Ground or Open All of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.

·

Ignition switch (communication) to ON.


·

Wire harness or connector

·

IG2 NO. 2 relay

·

Ignition or starter switch assembly (w/o Entry and Start System)

·

Certification ECU (Smart key ECU assembly) (w/ Entry and Start System)

·

Engine stop and start ECU


Does not come on DTC stored SAE Code: P2531

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

Depress the brake pedal and stop the vehicle.


h.

Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)


i.

Release the brake pedal with the shift lever in D to start the engine.


j.

Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



WIRING DIAGRAM

w/ Entry and Start System


A436843E01
1.313,6.76 4.313,7.042 3,0.281 10 false Certification ECU (Smart Key ECU Assembly) 1.271,6.552 1.729,6.75 0.458,0.198 10 false G54 2.063,6.281 2.521,6.479 0.458,0.198 10 false IG1D 1.573,6.302 2.031,6.5 0.458,0.198 10 false +B 2.458,6.177 2.917,6.375 0.458,0.198 10 false 17 1.417,6.167 1.76,6.458 0.344,0.292 10 false 4 0.635,0.896 1.542,1.146 0.906,0.25 10 false IG2-MAIN 0.635,2.063 1.281,2.573 0.646,0.51 10 false EFI-MAIN NO. 1 0.583,4.542 1.792,4.802 1.208,0.26 10 false J/B-B 0.635,6.729 1.844,6.99 1.208,0.26 10 false Battery 1.938,5.635 4.885,5.958 2.948,0.323 10 false Instrument Panel Junction Block Assembly 2.344,1.396 3.208,1.625 0.865,0.229 10 false IG2 NO. 1 2.292,2.542 3.5,2.802 1.208,0.26 10 false EFI-MAIN NO. 1 4,0.906 5.354,1.219 1.354,0.313 10 false ECU-IG2 NO. 1 4.25,2.021 5.604,2.333 1.354,0.313 10 false EFI NO. 1 3.344,4.521 4.698,4.833 1.354,0.313 10 false METER-IG2 2.625,5.01 3.833,5.271 1.208,0.26 10 false IG2 NO. 2 5.698,4.875 7.073,5.313 1.375,0.438 10 false Engine Stop and Start ECU 5.76,4.354 6.302,4.635 0.542,0.281 10 false A32 5.74,3.75 6.281,4.052 0.542,0.302 10 false A34 6.198,4.365 6.74,4.646 0.542,0.281 10 false IG2 6.188,3.74 6.729,4.021 0.542,0.281 10 false +B 5.823,3.542 6.365,3.823 0.542,0.281 10 false 1 5.75,4.156 6.292,4.438 0.542,0.281 10 false 18*1 5.958,2.75 6.5,3.031 0.542,0.281 10 false A24 6.323,2.771 6.865,3.052 0.542,0.281 10 false ECM 6.198,2.313 6.74,2.594 0.542,0.281 10 false MREL 5.927,2.188 6.469,2.469 0.542,0.281 10 false 15 6.188,0.729 6.729,1.01 0.542,0.281 10 false IGSW 6,0.635 6.542,0.917 0.542,0.281 10 false 2 2.24,1.042 2.781,1.323 0.542,0.281 10 false 1 2.26,2.177 2.802,2.458 0.542,0.281 10 false 1 2.24,1.76 2.781,2.042 0.542,0.281 10 false 3 3.021,1.76 3.563,2.042 0.542,0.281 10 false 5 3.031,2.198 3.573,2.479 0.542,0.281 10 false 2 3.052,0.625 3.594,0.906 0.542,0.281 10 false 3 2.24,0.635 2.781,0.917 0.542,0.281 10 false 5 3.021,1.042 3.563,1.323 0.542,0.281 10 false 2 1.896,4.344 3.104,4.604 1.208,0.26 10 false 4L 4.344,4.344 5.552,4.604 1.208,0.26 10 false 4D 4.354,4.771 5.563,5.031 1.208,0.26 10 false 4D 1.885,4.792 3.094,5.052 1.208,0.26 10 false 4F 1.938,4.115 3.146,4.375 1.208,0.26 10 false 1 4.365,5.052 5.573,5.313 1.208,0.26 10 false 17 4.344,4.146 5.552,4.406 1.208,0.26 10 false 32 4.385,4.583 5.594,4.844 1.208,0.26 10 false 3 2.469,3.813 3.677,4.073 1.208,0.26 10 false AM2 1.885,3.344 3.094,3.604 1.208,0.26 10 false 4A 1.885,3.125 3.094,3.385 1.208,0.26 10 false 44 5.271,4.354 5.813,4.635 0.542,0.281 10 false G62 5.24,4.146 5.781,4.427 0.542,0.281 10 false 18*2 4.427,7.406 5.635,7.667 1.208,0.26 10 false *2: for RHD 4.427,7.031 5.635,7.292 1.208,0.26 10 false *1: for LHD 4.344,5.26 5.552,5.521 1.208,0.26 10 false 4A 1.885,4.573 3.094,4.833 1.208,0.26 10 false 13


w/o Entry and Start System


A436844E01
2.083,5.635 4.833,5.885 2.75,0.25 10 false Instrument Panel Junction Block Assembly 0.625,6.76 3.375,7.01 2.75,0.25 10 false Battery 0.552,4.531 3.302,4.781 2.75,0.25 10 false J/B-B 0.646,2.052 1.313,2.594 0.667,0.542 10 false EFI-MAIN NO. 1 0.625,0.875 3.375,1.125 2.75,0.25 10 false IG2-MAIN 2.177,2.552 4.927,2.802 2.75,0.25 10 false EFI-MAIN NO. 1 2.365,1.417 5.115,1.667 2.75,0.25 10 false IG2 NO. 1 4.073,0.896 5.698,1.24 1.625,0.344 10 false ECU-IG2 NO. 1 4.167,2.042 5.792,2.385 1.625,0.344 10 false EFI NO. 1 3.344,4.521 4.969,4.865 1.625,0.344 10 false METER-IG2 6.344,2.813 6.719,3.167 0.375,0.354 10 false ECM 5.979,2.781 6.354,3.135 0.375,0.354 10 false A24 6.188,2.302 6.698,2.656 0.51,0.354 10 false MREL 5.865,2.198 6.375,2.552 0.51,0.354 10 false 15 6.177,0.74 6.688,1.094 0.51,0.354 10 false IGSW 6,0.625 6.51,0.979 0.51,0.354 10 false 2 5.76,3.771 6.135,4.125 0.375,0.354 10 false A34 5.75,4.344 6.125,4.698 0.375,0.354 10 false A32 5.771,4.885 7.156,5.281 1.385,0.396 10 false Engine Stop and Start ECU 6.177,3.75 6.552,4.104 0.375,0.354 10 false +B 6.198,4.354 6.573,4.708 0.375,0.354 10 false IG2 5.74,4.135 6.115,4.49 0.375,0.354 10 false 18*1 5.802,3.552 6.177,3.906 0.375,0.354 10 false 1 2.656,5.031 5.406,5.281 2.75,0.25 10 false IG2 NO. 2 4.354,5.25 4.969,5.594 0.615,0.344 10 false 4A 1.917,4.354 2.531,4.698 0.615,0.344 10 false 4L 4.365,4.354 4.979,4.698 0.615,0.344 10 false 4D 4.365,4.771 4.979,5.115 0.615,0.344 10 false 4D 1.958,4.125 2.573,4.469 0.615,0.344 10 false 1 4.396,5.031 5.01,5.375 0.615,0.344 10 false 17 4.344,4.135 4.958,4.479 0.615,0.344 10 false 32 4.396,4.552 5.01,4.896 0.615,0.344 10 false 3 1.302,6.625 4.052,6.875 2.75,0.25 10 false Ignition or Starter Switch Assembly 1.125,6.479 3.875,6.729 2.75,0.25 10 false G28 2.688,6.156 3.198,6.51 0.51,0.354 10 false 8 1.354,6.146 1.865,6.5 0.51,0.354 10 false 7 2.313,6.167 5.063,6.417 2.75,0.25 10 false IG1 1.521,6.167 4.271,6.417 2.75,0.25 10 false AM1 2.208,0.635 2.719,0.99 0.51,0.354 10 false 5 2.24,1.042 2.75,1.396 0.51,0.354 10 false 1 3.031,1.031 3.542,1.385 0.51,0.354 10 false 2 3.042,0.625 3.552,0.979 0.51,0.354 10 false 3 2.26,1.792 2.771,2.146 0.51,0.354 10 false 3 2.25,2.198 2.76,2.552 0.51,0.354 10 false 1 3.021,1.76 3.531,2.115 0.51,0.354 10 false 5 3.042,2.198 3.552,2.552 0.51,0.354 10 false 2 1.875,3.375 2.49,3.719 0.615,0.344 10 false 4A 2.458,3.771 3.073,4.115 0.615,0.344 10 false AM2 1.875,3.156 2.49,3.5 0.615,0.344 10 false 44 5.26,4.354 5.635,4.708 0.375,0.354 10 false G62 5.229,4.146 5.604,4.5 0.375,0.354 10 false 18*2 4.375,6.979 6.031,7.25 1.656,0.271 10 false 1: for LHD 4.344,7.313 5.698,7.677 1.354,0.365 10 false *2: for RHD 1.896,4.76 2.51,5.104 0.615,0.344 10 false 4F 1.896,4.573 2.51,4.917 0.615,0.344 10 false 13


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 392 203

e.

According to the display on the GTS, read the Data List.

Result:
GTS Display Result Proceed to
IG Switch ON A
OFF B




A

B

2.CHECK ENGINE STOP AND START ECU (IG2 TERMINAL VOLTAGE)
2.CHECK ENGINE STOP AND START ECU (IG2 TERMINAL VOLTAGE)
A419453C39
4.448,0.094 4.969,0.406 0.521,0.313 4.448,0.479 4.969,0.792 0.521,0.313 5.438,2.271 5.104,1.531 true 5.385,2.323 6.042,2.51 0.656,0.188 10 false IG2 4.542,0.542 4.917,0.74 0.375,0.198 10 false G62 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 4.552,0.188 4.927,0.385 0.375,0.198 10 false A32 5.083,0.167 5.458,0.365 0.375,0.198 10 false *1 5.094,0.542 5.469,0.74 0.375,0.198 10 false *2
*1 for LHD *2 for RHD
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32*1-18 (IG2) - Body ground
G62*2-18 (IG2) - Body ground
Ignition switch ON 9.5 to 14 V


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY))
3.CHECK ENGINE STOP AND START ECU (+B TERMINAL VOLTAGE)
A397704C56
3.26,0.094 3.646,0.365 0.385,0.271 4.104,0.688 4.302,1.479 true 0.865,0.135 1.177,0.333 0.313,0.198 10 false *a 4.313,1.458 4.927,1.656 0.615,0.198 10 false +B 3.344,0.156 3.958,0.354 0.615,0.198 10 false A34
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-1 (+B) - 5 (EFI-MAIN NO. 1 relay) Always Below 1 Ω
A34-1 (+B) or 5 (EFI-MAIN NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT EFI-MAIN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

NG

REPLACE EFI-MAIN NO. 1 RELAY

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32*1-18 (IG2) - 4D-32 Always Below 1 Ω
A32*1-18 (IG2) or 4D-32 - Body ground and other terminals Always 10 kΩ or higher
G62*2-18 (IG2) - 4D-32 Always Below 1 Ω
G62*2-18 (IG2) or 4D-32 - Body ground and other terminals Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)
A375649C22
0.615,1.146 0.948,1.396 0.333,0.25 0.271,0.125 0.583,0.323 0.313,0.198 10 false *a 0.688,1.177 1,1.375 0.313,0.198 10 false 4L
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4L-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4L-1 - 4D-32 Battery positive (+) → 4A-17
Battery negative (-) → 4D-3
Below 1 Ω
4L-1 - 4D-32 Battery not connected to 4A-17 and 4D-3 10 kΩ or higher



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - IGNITION OR STARTER SWITCH ASSEMBLY)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - G54-17 (IG1D) Always Below 1 Ω
4A-17 or G54-17 (IG1D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - G28-8 (IG1) Always Below 1 Ω
4A-17 or G28-8 (IG1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>A25A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY