Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0369994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)



WIRING DIAGRAM

E413743E03
5.74,2.01 6.354,2.208 0.615,0.198 10 false IG1D 2.76,0.302 3.917,1.01 1.156,0.708 10 false from Battery 2.615,2.281 4.104,2.729 1.49,0.448 10 false IG1 NO.1 Relay 2.635,3.604 4.219,4.021 1.583,0.417 10 false IG1 NO.2 Relay 2.625,4.802 4.208,5.354 1.583,0.552 10 false IG2 NO.2 Relay 5.094,4.135 6.01,4.573 0.917,0.438 10 false from Battery 2.667,7.844 3.813,8.208 1.146,0.365 10 false IG2 NO.1 Relay 4.573,7.177 5.479,7.51 0.906,0.333 10 false from Battery 1.229,1.771 2.146,1.969 0.917,0.198 10 false ECU-IG1 NO.1 1.365,4.313 2.281,4.51 0.917,0.198 10 false ECU-IG2 NO.3 1.448,3.052 2.615,3.469 1.167,0.417 10 false WASHER 5.333,2.958 7.156,3.875 1.823,0.917 10 false Certification ECU (Smart Key ECU Assembly) 1.177,6.219 4.635,6.583 3.458,0.365 10 false Instrument Panel Junction Block Assembly 4.344,1.969 4.958,2.167 0.615,0.198 10 false 4A 4.365,1.792 4.979,1.99 0.615,0.198 10 false 17 4.354,1.302 4.969,1.5 0.615,0.198 10 false 4K 4.417,1.083 5.031,1.281 0.615,0.198 10 false 1 0.667,1.615 1.281,1.813 0.615,0.198 10 false 4D 0.677,1.438 1.292,1.635 0.615,0.198 10 false 31 0.688,1.979 1.302,2.177 0.615,0.198 10 false 4D 0.729,1.813 1.344,2.01 0.615,0.198 10 false 3 0.688,2.885 1.302,3.083 0.615,0.198 10 false 4F 0.719,2.708 1.333,2.906 0.615,0.198 10 false 2 0.688,4.146 1.302,4.344 0.615,0.198 10 false 4F 0.698,3.958 1.313,4.156 0.615,0.198 10 false 15 0.667,5.531 1.281,5.729 0.615,0.198 10 false 4F 0.677,5.365 1.292,5.563 0.615,0.198 10 false 13 4.365,4.146 4.979,4.344 0.615,0.198 10 false 4L 4.365,3.969 4.979,4.167 0.615,0.198 10 false 1 2.656,7.375 3.271,7.573 0.615,0.198 10 false 1 3.583,7.354 4.198,7.552 0.615,0.198 10 false 2 3.583,7.063 4.198,7.26 0.615,0.198 10 false 5 2.667,7.063 3.281,7.26 0.615,0.198 10 false 3 5.469,1.896 6.083,2.094 0.615,0.198 10 false 17 5.344,2.792 5.958,2.99 0.615,0.198 10 false G54 4.729,5 7.052,5.521 2.323,0.521 10 false *1: except LHD, Manual Transaxle 4.719,5.302 7.042,5.823 2.323,0.521 10 false *2: for LHD, Manual Transaxle 4.719,1.094 5.333,1.292 0.615,0.198 10 false 1 4.656,1.292 5.271,1.49 0.615,0.198 10 false 4M 4.396,1.5 5.01,1.698 0.615,0.198 10 false *1 4.688,1.5 5.302,1.698 0.615,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function, Gasoline Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start, Power Source Control / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Power Source Control > Trouble Codes
50001 223

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B498244C41
1.604,0.115 1.969,0.354 0.365,0.24 0.979,1.979 1.177,1.979 1.177,1.979 1.177,0.958 false 1.656,0.156 2,0.354 0.344,0.198 10 false G54 0.635,1.906 1.229,2.104 0.594,0.198 10 false IG1D 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G54-17 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

except LHD, Manual Transaxle:

Disconnect the 4A, 4K, 4L and 4F instrument panel junction block assembly connectors.


c.

for LHD, Manual Transaxle:

Disconnect the 4A, 4M, 4L and 4F instrument panel junction block assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G54-17 (IG1D) - 4A-17 Always Below 1 Ω
4F-13 - Body ground Always Below 1 Ω
G54-17 (IG1D) or 4A-17 - Other terminals and body ground Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
except LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V
4L-1 - Body ground Always 11 to 14 V

for LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4M-1 - Body ground Always 11 to 14 V
4L-1 - Body ground Always 11 to 14 V



f.

Reconnect the G54 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
C412263C01
1.771,0.302 2.177,0.542 0.406,0.24 5.615,0.333 6.021,0.573 0.406,0.24 1.167,1.802 1.573,2.042 0.406,0.24 3.573,1.625 3.979,1.865 0.406,0.24 3.573,1.938 3.979,2.177 0.406,0.24 5.74,1.792 6.146,2.031 0.406,0.24 1.875,0.333 2.188,0.531 0.313,0.198 10 false 4A 5.729,0.365 6.042,0.563 0.313,0.198 10 false 4D 1.292,1.833 1.604,2.031 0.313,0.198 10 false 4F 4.063,1.677 4.375,1.875 0.313,0.198 10 false *A 3.698,1.969 4.01,2.167 0.313,0.198 10 false 4M 5.885,1.844 6.198,2.042 0.313,0.198 10 false 4L 3.688,1.667 4,1.865 0.313,0.198 10 false 4K 4.073,1.969 4.385,2.167 0.313,0.198 10 false *B
*A for LHD, Manual Transaxle *B except LHD, Manual Transaxle
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-17 - 4F-13 Always Below 1 Ω



d.

Connect a positive (+) lead from the battery to terminal 4A-17.


e.

Connect a negative (-) lead from the battery to terminal 4D-3.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4K-1 - 4D-31 Always Below 1 Ω
4K-1 - 4F-2 Always Below 1 Ω
4L-1 - 4F-15 Always Below 1 Ω

for LHD, Manual Transaxle:
Tester Connection Condition Specified Condition
4M-1 - 4D-31 Always Below 1 Ω
4M-1 - 4F-2 Always Below 1 Ω
4L-1 - 4F-15 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, POWER SUPPLY AND BODY GROUND)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Remove the IG2 NO.1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-13 - IG2 NO.1 relay installation terminal 1 Always Below 1 Ω
IG2 NO.1 relay installation terminal 2 - Body ground Always Below 1 Ω
4F-13 or IG2 NO.1 relay installation terminal 1 - Other terminals and body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IG2 NO.1 relay installation terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT IG2 NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IG2 NO. 1 RELAY
a.
C279145C29
2.031,0.625 1.677,0.385 false 2.604,0.677 2.917,0.469 false 2.385,1.135 2.875,1.135 false 2.448,1.635 2.906,1.635 false 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 2.99,0.333 3.146,0.531 0.156,0.198 10 false 1 1.552,0.25 1.708,0.448 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.26,0.167 0.458,0.375 0.198,0.208 10 false *1
*1 IG2 NO. 1 Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω
Battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE IG2 NO. 1 RELAY