Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM (for A25A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371962 STOP AND START SYSTEM(for A25A-FKS) C

STOP AND START  STOP AND START SYSTEM(for A25A-FKS)  P279612  Electromagnetic Oil Pump Circuit Short to Battery  


DESCRIPTION

The oil pump with solenoid assembly is installed inside the automatic transaxle assembly.

The oil pump with solenoid assembly operates from the time the engine is stopped due to stop and start control until the vehicle starts moving again in order to ensure oil pressure within the automatic transaxle assembly and allow for a smooth start-off.

The engine stop and start ECU supplies power from the backup boost converter to the oil pump with solenoid assembly through Tr1 and performs Tr2 duty control to operate the oil pump with solenoid assembly.

The engine stop and start ECU performs Tr1 and Tr2 control when operating or not operating the oil pump with solenoid assembly and during the preliminary check, and also monitors the EGND terminal to record DTCs.

As a preliminary check, the first time the vehicle speed reaches 2 km/h (1.2 mph) or more on each trip and every time the vehicle speed reaches 2 km/h (1.2 mph) or more after stop and start control is performed, the engine stop and start ECU turns Tr1 ON and checks that there are no malfunctions in the oil pump with solenoid assembly circuit.

The engine stop and start solenoid filter absorbs high-voltage counter-electromotive force generated when the oil pump with solenoid assembly operates.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P279612 Electromagnetic Oil Pump Circuit Short to Battery Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
·

Oil pump with solenoid assembly not operating (Tr1: Off, Tr2: Off).

·

EGND terminal voltage 10 V or higher.


·

Wire harness or connector

·

Transmission wire

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P2799

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

Depress the brake pedal and stop the vehicle.


h.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


i.

Release the brake pedal with the shift lever in D to start the engine.


j.

Check that no DTCs are output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



WIRING DIAGRAM

A436153E01
0.531,3.24 2.26,3.469 1.729,0.229 10 false Engine Stop and Start ECU 2.042,2.188 2.656,2.385 0.615,0.198 10 false EGND 0.49,2.406 0.948,2.604 0.458,0.198 10 false Tr2 0.479,1.542 0.938,1.74 0.458,0.198 10 false Tr1 2.031,1.5 2.646,1.698 0.615,0.198 10 false EMOP 2.677,1.427 3.031,1.646 0.354,0.219 10 false 9*1 2.604,2.073 3.073,2.313 0.469,0.24 10 false 8*1 3.833,1.531 3.99,1.729 0.156,0.198 10 false 7 3.833,2.177 3.99,2.375 0.156,0.198 10 false 8 4.042,1.531 4.656,1.729 0.615,0.198 10 false MOPI 5.01,1.521 5.625,1.719 0.615,0.198 10 false MOP+ 5.521,1.521 5.677,1.719 0.156,0.198 10 false 2 4.031,2.177 4.646,2.375 0.615,0.198 10 false GND 5.021,2.177 5.635,2.375 0.615,0.198 10 false MOP- 5.521,2.177 5.677,2.375 0.156,0.198 10 false 1 3.625,2.688 4.083,2.885 0.458,0.198 10 false A36 3.625,2.833 6.063,3.146 2.438,0.313 10 false Engine Stop and Start Solenoid Filter 5.333,4.844 5.948,5.042 0.615,0.198 10 false EMP+ 5.833,4.844 6.146,5.042 0.313,0.198 10 false 29 5.823,4.198 6.135,4.396 0.313,0.198 10 false 28 5.344,4.198 5.958,4.396 0.615,0.198 10 false EMP- 4.563,4.844 4.719,5.042 0.156,0.198 10 false 2 4.573,4.177 4.729,4.375 0.156,0.198 10 false 1 4.938,5.417 5.396,5.615 0.458,0.198 10 false C30 4.948,5.583 6.646,5.813 1.698,0.229 10 false Transmission Wire 3.229,5.406 4.677,6 1.448,0.594 10 false Oil Pump with Solenoid Assembly 2.073,2.802 2.688,3 0.615,0.198 10 false GND1 2.604,2.802 3.063,3 0.458,0.198 10 false A33 2.677,2.573 2.833,2.771 0.156,0.198 10 false 8 2.583,1.646 3.042,1.844 0.458,0.198 10 false A32 2.573,2.292 3.031,2.49 0.458,0.198 10 false A32 0.604,0.646 2.156,0.854 1.552,0.208 10 false Backup Boost Converter 3,1.646 3.458,1.844 0.458,0.198 10 false G62 3,2.292 3.458,2.49 0.458,0.198 10 false G62 3.021,1.438 3.375,1.656 0.354,0.219 10 false 9*2 2.99,2.083 3.458,2.323 0.469,0.24 10 false 8*2 1.021,4.813 2.552,5.01 1.531,0.198 10 false *1: for LHD 1.021,5.156 2.552,5.354 1.531,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION

·

When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>DTC CHECK / CLEAR



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P279612)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the DTCs

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTC P279612 is output A
DTCs P279612 and P323A19 are output B




A

2.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OTHER TERMINALS)
2.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)
A419453C40
4.677,0.49 5.125,0.76 0.448,0.271 4.677,0.135 5.125,0.406 0.448,0.271 4.542,2.229 4.781,1.448 true 4.344,2.26 5,2.448 0.656,0.188 10 false EGND 4.75,0.542 5.125,0.74 0.375,0.198 10 false G62 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 4.74,0.208 5.115,0.406 0.375,0.198 10 false A32 5.219,0.188 5.594,0.385 0.375,0.198 10 false *1 5.24,0.5 5.615,0.698 0.375,0.198 10 false *2
*1 for LHD *2 for RHD
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Result Proceed to
A32*1-8 (EGND) - Body ground
G62*2-8 (EGND) - Body ground
Ignition switch ON 10 to 14 V A
Below 1 V B


*1: for LHD

*2: for RHD




A

3.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)

B

3.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)
A419453C40
4.677,0.49 5.125,0.76 0.448,0.271 4.677,0.135 5.125,0.406 0.448,0.271 4.542,2.229 4.781,1.448 true 4.344,2.26 5,2.448 0.656,0.188 10 false EGND 4.75,0.542 5.125,0.74 0.375,0.198 10 false G62 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 4.74,0.208 5.115,0.406 0.375,0.198 10 false A32 5.219,0.188 5.594,0.385 0.375,0.198 10 false *1 5.24,0.5 5.615,0.698 0.375,0.198 10 false *2
*1 for LHD *2 for RHD
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the transmission wire connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Result Proceed to
A32*1-8 (EGND) - Body ground
G62*2-8 (EGND) - Body ground
Ignition switch ON 10 to 14 V A
Below 1 V B


*1: for LHD

*2: for RHD




A

4.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)

B

4.CHECK HARNESS AND CONNECTOR (EGND TERMINAL VOLTAGE)
A436064C01
1.469,0.438 1.979,0.74 0.51,0.302 1.469,0.073 1.979,0.375 0.51,0.302 1.906,1.344 1.958,1.844 true 1.563,0.531 2.01,0.708 0.448,0.177 10 false G62 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.792,1.896 2.406,2.094 0.615,0.198 10 false EGND 1.573,0.135 2.021,0.313 0.448,0.177 10 false A32 2.063,0.135 2.51,0.313 0.448,0.177 10 false *1 2.073,0.49 2.521,0.667 0.448,0.177 10 false *2
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Result Proceed to
A32*1-8 (EGND) - Body ground
G62*2-8 (EGND) - Body ground
Ignition switch ON 10 to 14 V A
Below 1 V B


*1: for LHD

*2: for RHD




A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU (EGND) - TRANSMISSION WIRE (EMP-))

B

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OTHER TERMINALS)
A419453C42
4.677,0.49 5.125,0.76 0.448,0.271 4.677,0.146 5.125,0.417 0.448,0.271 4.458,2.229 4.698,1.448 true 4.25,2.26 4.906,2.448 0.656,0.188 10 false EMOP 4.75,0.542 5.125,0.74 0.375,0.198 10 false G62 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 4.729,0.219 5.104,0.417 0.375,0.198 10 false A32 5.219,0.208 5.594,0.406 0.375,0.198 10 false *1 5.219,0.563 5.594,0.76 0.375,0.198 10 false *2
*1 for LHD *2 for RHD
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32*1-9 (EMOP) - Other terminals*3
G62*2-9 (EMOP) - Other terminals*3
Always 10 kΩ or higher


*1: for LHD

*2: for RHD

*3: Except A32*1-8 (EGND) or G62*2-8 (EGND) terminal



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OTHER TERMINALS)
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - OTHER TERMINALS)
A419453C42
4.677,0.49 5.125,0.76 0.448,0.271 4.677,0.146 5.125,0.417 0.448,0.271 4.458,2.229 4.698,1.448 true 4.25,2.26 4.906,2.448 0.656,0.188 10 false EMOP 4.75,0.542 5.125,0.74 0.375,0.198 10 false G62 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 4.729,0.219 5.104,0.417 0.375,0.198 10 false A32 5.219,0.208 5.594,0.406 0.375,0.198 10 false *1 5.219,0.563 5.594,0.76 0.375,0.198 10 false *2
*1 for LHD *2 for RHD
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32*1-9 (EMOP) - Other terminals
G62*2-9 (EMOP) - Other terminals
Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - TRANSMISSION WIRE)
7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - TRANSMISSION WIRE)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A32*1-9 (EMOP) - Other terminals
G62*2-9 (EMOP) - Other terminals
Always 10 kΩ or higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR