Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for M20A-FKS)
RM3620E _51 Engine / Hybrid System _076400 STOP AND START _0371963 STOP AND START SYSTEM(for M20A-FKS) C

STOP AND START  STOP AND START SYSTEM(for M20A-FKS)  P161D9E  Starter Delay Circuit Stuck On  


DESCRIPTION

HINT:

This DTC is applicable to Continuously Variable Transaxle models only.


By using the starter delay circuit, the engine stop and start ECU can activate the ST NO. 2 relay (for starter motor operation) after activating the ST NO. 1 relay (for starter pinion operation) to operate the starter assembly.

By monitoring the condition of the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation), the engine stop and start ECU detects if the transistor of the starter delay circuit is stuck. If the transistor of the starter delay circuit is stuck on, the engine stop and start ECU blinks the stop and start cancel indicator and stores DTC P161D9E. If the transistor of the starter delay circuit is stuck on, the ST NO. 1 relay (for starter pinion operation) and ST NO. 2 relay (for starter motor operation) will be activated simultaneously.

w/ Entry and Start System



A436056E01
2.115,0.573 2.875,0.771 0.76,0.198 10 false BBC NO. 1 2.125,0.833 2.885,1.031 0.76,0.198 10 false BBC NO. 2 0.948,1.177 1.708,1.375 0.76,0.198 10 false STAR 0.396,1.531 2.188,1.958 1.792,0.427 10 false Certification ECU (Smart Key ECU Assembly) 2.521,2.333 3.833,2.823 1.313,0.49 10 false Park/Neutral Position Switch Assembly 4.24,0.323 4.719,0.49 0.479,0.167 10 false BIN1 4.229,0.594 4.708,0.76 0.479,0.167 10 false BIN2 4.229,2.479 4.708,2.646 0.479,0.167 10 false STA 4.24,3.229 4.719,3.396 0.479,0.167 10 false STA2 4.635,3.656 6.333,3.896 1.698,0.24 10 false Engine Stop and Start ECU 1.281,3.542 2.042,3.74 0.76,0.198 10 false ST NO.1 0.438,3.125 1.198,3.323 0.76,0.198 10 false ST NO. 1 0.448,4.177 1.208,4.375 0.76,0.198 10 false ST NO. 2 1.281,4.604 2.042,4.802 0.76,0.198 10 false ST NO. 2 2.865,5.219 3.344,5.385 0.479,0.167 10 false SL2 0.521,6.531 1.167,6.771 0.646,0.24 10 false Battery 4.26,7.51 5.354,7.74 1.094,0.229 10 false Starter Assembly 4.542,5.719 6.906,6.031 2.365,0.313 10 false Starter Inrush Current Reduction Relay 2.865,6.573 3.344,6.74 0.479,0.167 10 false SL1

w/o Entry and Start System



A436057E01
4.646,3.667 6.76,4.01 2.115,0.344 10 false Engine Stop and Start ECU 2.115,0.573 4.229,0.917 2.115,0.344 10 false BBC NO. 1 2.115,0.833 4.229,1.177 2.115,0.344 10 false BBC NO. 2 1.406,1.542 2.917,1.979 1.51,0.438 10 false Ignition or Starter Switch Assembly 0.823,1.302 2.938,1.646 2.115,0.344 10 false AM2 0.604,1.677 2.719,2.021 2.115,0.344 10 false J/B-B 2.458,2.323 3.771,2.76 1.313,0.438 10 false Park/Neutral Position Switch Assembly 0.458,3.125 2.573,3.469 2.115,0.344 10 false ST NO. 1 0.448,4.188 2.563,4.531 2.115,0.344 10 false ST NO. 2 1.292,3.573 2.281,3.813 0.99,0.24 10 false ST NO.1 1.292,4.635 3.406,4.979 2.115,0.344 10 false ST NO. 2 2.844,5.25 4.958,5.594 2.115,0.344 10 false SL2 2.854,6.604 4.969,6.948 2.115,0.344 10 false SL1 0.552,6.552 2.667,6.896 2.115,0.344 10 false Battery 4.25,0.323 6.365,0.667 2.115,0.344 10 false BIN1 4.25,0.583 6.365,0.927 2.115,0.344 10 false BIN2 4.25,2.469 6.365,2.813 2.115,0.344 10 false STA 4.26,3.24 6.375,3.583 2.115,0.344 10 false STA2 4.563,5.76 6.979,6.104 2.417,0.344 10 false Starter Inrush Current Reduction Relay 4.073,7.5 6.573,7.708 2.5,0.208 10 false Starter Assembly 1.5,1.073 3.615,1.417 2.115,0.344 10 false AM1 2.167,1.063 4.281,1.406 2.115,0.344 10 false ST1

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P161D9E Starter Delay Circuit Stuck On Both of the following conditions are met (1 trip detection logic):
·

Ignition switch ON.

·

Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds and 3 times or more.


Engine stop and start ECU Blinks DTC stored SAE Code: P161D

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 392

e.

Start the engine and warm it up.


f.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



g.

Depress the brake pedal and stop the vehicle.


h.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


i.

Release the brake pedal with the shift lever in D to start the engine.


j.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



k.

Depress the brake pedal and stop the vehicle.


l.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


m.

Release the brake pedal with the shift lever in D to start the engine.


n.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



o.

Depress the brake pedal and stop the vehicle.


p.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


q.

Release the brake pedal with the shift lever in D to start the engine.


r.

Check that no DTCs are output.

Powertrain > Stop and Start > Trouble Codes
50001 392


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION

·

Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>DTC CHECK / CLEAR



PROCEDURE

1.CHECK ENGINE STOP AND START ECU (STA, STA2 SIGNAL)
A419453C37
3.24,0.5 3.688,0.771 0.448,0.271 4.198,2.219 3.76,1.229 true 3.479,2.24 3.427,1.344 true 2.781,2.229 3.26,1.333 true 3.354,2.281 4.135,2.479 0.781,0.198 10 false STA 4.042,2.281 4.698,2.469 0.656,0.188 10 false DGND 3.344,0.552 3.719,0.75 0.375,0.198 10 false A34 0.104,0.073 0.885,0.271 0.781,0.198 10 false *a 2.604,2.292 3.385,2.49 0.781,0.198 10 false STA2
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Connect an oscilloscope to the STA, STA2 and DGND terminals of the stop and start ECU connector.


b.
A285702E44
0.042,0.677 0.5,0.875 0.458,0.198 10 false STA 0.042,1.281 0.5,1.479 0.458,0.198 10 false STA2 1.198,1.771 2.958,1.958 1.76,0.188 10 false 0.016 seconds or more 0.031,0.875 2.031,1.146 2,0.271 10 false (ST NO. 1 Relay) 0.031,1.458 1.865,1.656 1.833,0.198 10 false (ST NO. 2 Relay)

Check the waveform immediately after turning the ignition switch START.

Item Condition
Tester Connection A34-21 (STA) - A34-6 (DGND)
A34-23 (STA2) - A34-6 (DGND)
Condition Engine started by ignition switch operation

Result:
Result Proceed to
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes 0.016 seconds or more A
Time between ST NO. 1 relay (for starter pinion) turning on and ST NO. 2 relay (for starter motor) turning on becomes less than 0.016 seconds B




A

B