Refer to DTC P323A19.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>P323A19
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | Note |
|---|---|---|---|---|---|---|
| P30DF62 | Backup Boost Converter Circuit Board(Thermistor) Signal Compare Failure | The following condition is met for 1 second or more (1 trip detection logic):
·
Difference in temperature between thermistor 1 and thermistor 2 of the engine stop and start ECU is 40°C (72°F) or higher. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P30DF |
| P30EF4B | Backup Boost Converter Circuit Board Over Temperature | The following condition is met for 1 second or more (1 trip detection logic):
·
Engine stop and start ECU thermistor temperature is 135°C (275°F) or higher. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P30EF |
| P323A00 | Backup Boost Converter "A" | The following condition is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323A16 | Backup Boost Converter "A" Circuit Voltage Below Threshold | One of the following conditions is met for 1 second or more (1 trip detection logic):
·
B41 or IG41 voltage is 6.0 V or less and backup boost converter output overcurrent is not detected. ·
B42 or B43 voltage is 6.0 V or less, backup boost converter is not overheating and backup boost converter output overcurrent is not detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323AA2 | Backup Boost Converter "A" System Voltage Low | The following condition is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
| P323B29 | Backup Boost Converter "A" Control Circuit Signal Invalid | The following condition is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323C |
| P323B38 | Backup Boost Converter "A" Control Circuit Signal Cycle Invalid | The following condition is met for 1 second or more (1 trip detection logic):
·
Backup boost converter malfunction is detected. |
·
Wire harness or connector ·
Battery ·
BBC NO. 1 fuse ·
BBC NO. 2 fuse ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323C |
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
for Continuously variable transaxle:
Depress the brake pedal and stop the vehicle.
for Manual transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Keep the engine stopped by stop and start control for 1 second or more. (for Continuously variable transaxle: Keep the shift lever in D.)
for Continuously variable transaxle:
Release the brake pedal with the shift lever in D to start the engine.
for Manual transaxle:
Depress the clutch pedal and start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
for Continuously variable transaxle:
Depress the brake pedal and stop the vehicle.
for Manual transaxle:
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control. (for Continuously variable transaxle: Keep the shift lever in D.)
for Continuously variable transaxle:
Release the brake pedal with the shift lever in D to start the engine.
for Manual transaxle:
Depress the clutch pedal and start the engine.
Refer to DTC P323A19.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>P323A19
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
for Continuously variable transaxle:
Bleed the oil pump with motor assembly (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>DTC CHECK / CLEAR
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>FREEZE FRAME DATA
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-1 (BIN2) - Body ground | Always | 9.5 to 14 V |
| A33-3 (BIN1) - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | for LHD |
| *2 | for RHD |
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32*1-21 (IG1) - Body ground
G62*2-21 (IG1) - Body ground |
Ignition switch ON | 9.5 to 14 V |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-6 (DGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the radio and display receiver assembly connector. (w/ Display Audio System)
Disconnect the radio receiver assembly connector. (w/o Display Audio System)
Disconnect the electrical key and tire pressure monitoring system receiver assembly connector. (w/ Tire Pressure Warning System)
Disconnect the central gateway ECU (network gateway ECU) connector.
Disconnect the clearance warning ECU assembly connector.
Disconnect the forward recognition camera connector. (w/ Toyota Safety Sense)
Disconnect the millimeter wave radar sensor assembly connector. (w/ Toyota Safety Sense)
Disconnect the blind spot monitor sensor LH connector.
Disconnect the blind spot monitor sensor RH connector.
Disconnect the air conditioning control assembly connector.
Disconnect the inner rear view mirror assembly connector. (w/ EC Mirror)
Disconnect the inner rear view mirror assembly connector. (w/ Digital Inner Mirror)
Disconnect the instrument panel junction block assembly (main body ECU (multiplex network body ECU)) connector. (for Manual transaxle)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-12 (B42) - G3-4 (+B1)*1 | Always | Below 1 Ω |
| A32-12 (B42) - G66-4 (+B1)*2 | Always | Below 1 Ω |
| A32-2 (B41) - M8-7 (+B)*3 | Always | Below 1 Ω |
| A32-3 (IG41) - M8-1 (IG)*3 | Always | Below 1 Ω |
| A32-3 (IG41) - G72-11 (IG1) | Always | Below 1 Ω |
| A32-3 (IG41) - H4-1 (IG) | Always | Below 1 Ω |
| A32-3 (IG41) - P8-7 (IGB)*4 | Always | Below 1 Ω |
| A32-3 (IG41) - B9-8 (IGB)*4 | Always | Below 1 Ω |
| A32-3 (IG41) - Q1-5 (BLB) | Always | Below 1 Ω |
| A32-3 (IG41) - Q13-5 (BRB) | Always | Below 1 Ω |
| A32-3 (IG41) - G24-9 (IG+) | Always | Below 1 Ω |
| A32-3 (IG41) - P2-4 (IG)*5 | Always | Below 1 Ω |
| A32-3 (IG41) - P3-1 (IG)*6 | Always | Below 1 Ω |
| A32-3 (IG41) - 4A-15*8 | Always | Below 1 Ω |
| A32-11 (B43) - P1-6 (+B)*7 | Always | Below 1 Ω |
| A32-11 (B43) - H7-10 (+B) | Always | Below 1 Ω |
| A32-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or G72-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or H4-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or B9-8 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or G24-9 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-3 (IG41) or 4A-15*8 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals | Always | 10 kΩ or higher |
| A32-11 (B43) or H7-10 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G62-12 (B42) - G3-4 (+B1)*1 | Always | Below 1 Ω |
| G62-12 (B42) - G66-4 (+B1)*2 | Always | Below 1 Ω |
| G62-2 (B41) - M8-7 (+B)*3 | Always | Below 1 Ω |
| G62-3 (IG41) - M8-1 (IG)*3 | Always | Below 1 Ω |
| G62-3 (IG41) - G72-11 (IG1) | Always | Below 1 Ω |
| G62-3 (IG41) - H4-1 (IG) | Always | Below 1 Ω |
| G62-3 (IG41) - P8-7 (IGB)*4 | Always | Below 1 Ω |
| G62-3 (IG41) - Q1-5 (BLB) | Always | Below 1 Ω |
| G62-3 (IG41) - Q13-5 (BRB) | Always | Below 1 Ω |
| G62-3 (IG41) - G24-9 (IG+) | Always | Below 1 Ω |
| G62-3 (IG41) - P2-4 (IG)*5 | Always | Below 1 Ω |
| G62-3 (IG41) - P3-1 (IG)*6 | Always | Below 1 Ω |
| G62-3 (IG41) - 4A-15*8 | Always | Below 1 Ω |
| G62-11 (B43) - P1-6 (+B)*7 | Always | Below 1 Ω |
| G62-11 (B43) - H7-10 (+B) | Always | Below 1 Ω |
| G62-12 (B42) or G3-4 (+B1)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-12 (B42) or G66-4 (+B1)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-2 (B41) or M8-7 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or M8-1 (IG)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or G72-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or H4-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P8-7 (IGB)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or Q1-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or Q13-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or G24-9 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P2-4 (IG)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or P3-1 (IG)*6 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-3 (IG41) or 4A-15*8 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-11 (B43) or P1-6 (+B)*7 - Body ground and other terminals | Always | 10 kΩ or higher |
| G62-11 (B43) or H7-10 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
*1: w/ Display Audio System
*2: w/o Display Audio System
*3: w/ Tire Pressure Warning System
*4: w/ Toyota Safety Sense
*5: w/ Forward Recognition Camera
*6: w/o Forward Recognition Camera
*7: w/ Digital Inner Mirror
*8: for Manual transaxle
| Proceed to |
|---|
| OK |
| NG |
OK
NG