Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
89710
1.REMOVE POSITION CONTROL ECU ASSEMBLY (w/ Memory)
73240
2.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
71868N
3.REMOVE FRONT SEAT FRONT CUSHION SHIELD LH
|
Place Hand Here |
|
Remove in this Direction |
Remove the clip.
Place your hand at the position shown in the illustration and pull in the removal direction to detach the guide.
|
Place Hand Here |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hand at the position shown in the illustration and pull in the removal direction to detach the guide and remove the front seat front cushion shield LH.
71812D
4.REMOVE FRONT SEAT CUSHION SHIELD LH
| *a | Claw A |
| *b | Claw B |
|
Place Hand Here |
|
Remove in this Direction |
|
Protective Tape |
Using a screwdriver, detach the claw A as shown in the illustration.
Tape the screwdriver tip before use.
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw B.
|
Place Hand Here |
|
Remove in this Direction |
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw and guide.
|
Place Hand Here |
|
Remove in this Direction |
|
Protective Tape |
Using a screwdriver, detach the claw.
Tape the screwdriver tip before use.
Place your hand at the position shown in the illustration and pull in the removal direction to detach the guide.
Disconnect the connector and remove the front seat cushion shield LH.
84921B
5.REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
Remove in this Direction |
Using moulding remover A, detach the claw and remove the slide and vertical power seat switch knob.
84921A
6.REMOVE RECLINING POWER SEAT SWITCH KNOB
|
Remove in this Direction |
Using moulding remover A, detach the claw and remove the reclining power seat switch knob.
84922C
7.REMOVE FRONT POWER SEAT SWITCH LH
71862
8.REMOVE FRONT SEAT INNER CUSHION SHIELD LH
| *a | Claw A |
| *b | Claw B |
|
Place Hand Here |
|
Remove in this Direction |
|
Protective Tape |
Using a screwdriver, detach the claw A as shown in the illustration.
Tape the screwdriver tip before use.
Place your hand at the position shown in the illustration and pull in the removal direction to detach the claw B and guide.
|
Remove in this Direction |
Detach the claw and remove the front seat inner cushion shield LH.
9.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Detach the band.
| *A | w/ Seat Heater System |
Detach the claw and clamp.
w/o Seat Heater System:
Disconnect the connector.
w/ Seat Heater System:
Disconnect the 2 connectors.
Detach the hook.
Remove the 4 bolts.
|
Protective Tape |
Using a screwdriver, detach the guide and remove the separate type front seatback assembly.
Tape the screwdriver tip before use.
10.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Detach the hook.
w/ Seat Heater System:
Detach the clamp.
Open the 2 fasteners.
|
Remove in this Direction |
Detach the claw to remove the 2 front seat headrest supports as shown in the illustration.
Remove the separate type front seatback cover with pad.
71074S
11.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
for Standard Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seatback cover.
Tape the thin-bladed screwdriver tip before use.
for Sports Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seatback cover from the separate type front seatback pad as shown in the illustration.
|
Protective Tape | - | - |
Be careful not to dirty or damage the separate type front seatback cover.
Tape the thin-bladed screwdriver tip before use.
87510N
12.REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
73920A
13.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH
8219B
14.REMOVE FRONT NO. 2 SEAT WIRE LH
| *A | w/ Climate Control Seat System |
w/o Climate Control Seat System:
Disconnect the 2 connectors.
w/ Climate Control Seat System:
Disconnect the 3 connectors.
Detach the clamp and remove the front No. 2 seat wire LH.
72760D
15.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
|
Remove in this Direction |
Detach the clamp.
Pull in the removal direction shown in the illustration to remove the lumbar support adjuster assembly LH.
Remove the 2 front seatback edge protectors together with the lumbar support adjuster assembly LH.
|
Remove in this Direction |
Remove the front seatback felt LH.
85867A
16.REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)
Detach the claw and hook to remove the seatback climate control blower LH.
71587B
17.REMOVE FRONT SEATBACK EDGE PROTECTOR
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the 2 front seatback edge protectors.
Tape the thin-bladed screwdriver tip before use.
71759D
18.REMOVE FRONT NO. 2 SEATBACK HOOK
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw to remove the 2 front No. 2 seatback hooks.
Do not reuse the removed front No. 2 seatback hook.
Tape the thin-bladed screwdriver tip before use.
19.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
w/ Seat Heater System:
Disconnect the connector and detach the clamp.
Detach the hook to remove the separate type front seat cushion cover with pad.
71072S
20.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
| *a | Band |
|
Remove in this Direction |
Detach the band.
for Standard Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
|
Protective Tape | - | - |
Do not dirty or damage the separate type front seat cushion cover.
Tape the thin-bladed screwdriver tip before use.
for Sports Seat Type:
Using a thin-bladed screwdriver, detach the hook to remove the separate type front seat cushion cover from the separate type front seat cushion pad as shown in the illustration.
|
Protective Tape | - | - |
Do not dirty or damage the separate type front seat cushion cover.
Tape the thin-bladed screwdriver tip before use.
87510L
21.REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
71876G
22.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER
|
Remove in this Direction |
Detach the claw and hook to remove the LH seat reclining adjuster inside cover as shown in the illustration.
71875G
23.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER
| *a | Guide |
| *b | Hook |
|
Remove in this Direction |
Detach the guide, claw and hook to remove the LH seat reclining adjuster inside cover as shown in the illustration.
71874A
24.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH
| *a | Hook |
| *b | Guide |
|
Remove in this Direction |
|
Protective Tape |
Detach the hook.
Using a thin-bladed screwdriver, detach the claw as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front seat lower cushion shield LH.
71873U
25.REMOVE FRONT SEAT LOWER CUSHION SHIELD RH
| *a | Hook |
| *b | Guide |
|
Remove in this Direction |
|
Protective Tape |
Detach the hook.
Using a thin-bladed screwdriver, detach the claw as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front seat lower cushion shield RH.
85860B
26.REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)
Detach the clamp and disconnect the connector.
Remove the 2 bolts.
Detach the hook and remove the seat cushion climate control blower assembly LH.
71052A
27.REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
| *a | Clamp |
| *b | Hook |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
w/ Seat Heater System:
Detach the clamp.
Pull in the removal direction (1) shown in the illustration to detach the hook on the front side of the front seat cushion spring sub-assembly LH.
Pull in the removal direction (2) shown in the illustration to detach the hook on the rear side and remove the front seat cushion spring sub-assembly LH.
7181B
28.REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER LH
w/ Seat Position Airbag Sensor:
Disconnect the connector.
Disconnect the 3 connectors.
Detach the clamp.
Remove the 2 screws.
| *a | Guide | *b | Hook |
|
Remove in this Direction |
|
Protective Tape |
Detach the guide.
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the hook and remove the front seat cushion wire harness holder LH.
Remove the front seat cushion wire harness holder LH together with the seat heater control sub-assembly LH, front seat No. 3 wire LH and front seat wire LH.
87501B
29.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System, w/ Climate Control Seat System)
|
Remove in this Direction |
|
Protective Tape |
Disconnect the connector.
Using a thin-bladed screwdriver, detach the claw and remove the seat heater control sub-assembly LH.
Tape the thin-bladed screwdriver tip before use.
8219BA
30.REMOVE FRONT NO. 3 SEAT WIRE LH (w/ Seat Position Airbag Sensor)
Detach the claw and clamp to remove the front No. 3 seat wire LH.
82192
31.REMOVE FRONT SEAT WIRE LH
Detach the claw and clamp to remove the front seat wire LH.
71874C
32.REMOVE FRONT SEAT LOWER CUSHION SHIELD
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the front seat lower cushion shield.
72266
33.REMOVE SEAT UPPER TRACK RAIL COVER LH
Use the same procedure for the other side.
Place a matchmark on the front seat adjuster assembly LH.
w/ Memory:
Connect the No. 4 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the frontmost position.
After performing this procedure, initialize the seat ECU (position control ECU assembly).
w/o Memory:
Connect the No. 2 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the frontmost position.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the seat upper track rail cover LH.
Tape the thin-bladed screwdriver tip before use.
72125T
34.REMOVE FRONT SEAT REAR UPPER TRACK COVER LH
Use the same procedure for the other side.
w/ Memory:
Connect the No. 1 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.
After performing this procedure, initialize the seat ECU (position control ECU assembly).
w/o Memory:
Connect the No. 1 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 2 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the front seat rear upper track cover LH.
Tape the thin-bladed screwdriver tip before use.
85822C
35.REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY LH
85822B
36.REMOVE POWER SEAT TILT MOTOR ASSEMBLY LH