Home › Vehicle Interior › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076405 SEAT _0372021 FRONT POWER SEAT MOTOR ASSEMBLY A

SEAT  FRONT POWER SEAT MOTOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power seat lifter motor assembly and power seat tilt motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)

·

Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)

·

Power seat lifter motor assembly (driver seat) (Including removal and installation)

·

Power seat tilt motor assembly (driver seat) (Including removal and installation)


Initialize position control ECU Front power seat control system (for HV model with memory) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:(Click here)
for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
·

Reclining motor (Front seatback frame sub-assembly (driver seat)) (Including removal and installation)

·

Slide motor (Front seat adjuster assembly (driver seat)) (Including removal and installation)

·

Power seat lifter motor assembly (driver seat) (Including removal and installation)

·

Power seat tilt motor assembly (driver seat) (Including removal and installation)


Initialize position control ECU Front power seat control system (for Gasoline model with memory) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


CAUTION:
·
B521791

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·
B458500

Be sure to read precaution thoroughly before servicing.


·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 2.REMOVE FRONT SEAT ASSEMBLY LH

Hide 71868N 3.REMOVE FRONT SEAT FRONT CUSHION SHIELD LH

Hide 71812D 4.REMOVE FRONT SEAT CUSHION SHIELD LH

Hide 71862 5.REMOVE FRONT SEAT INNER CUSHION SHIELD LH

Hide 6.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

Hide 7.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

Hide 71876G 8.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER

Hide 85822C 9.REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY LH

a.
B526569

Disconnect the connector.


b.
B526570C01
0.594,0.51 0.875,0.51 0.875,0.51 1.177,0.896 true 0.313,0.865 0.594,0.865 0.594,0.865 0.896,1.25 true 0.104,0.76 0.292,0.958 0.188,0.198 10 false *1 0.385,0.406 0.573,0.615 0.188,0.208 10 false *2
*1 Front Seat Adjuster Plate LH
*2 Vertical Adjuster Spacer


Remove the 3 nuts, front seat adjuster plate LH and vertical adjuster spacer.


c.

Remove the power seat lifter motor assembly LH.

NOTICE:

Do not damage or dirty the gears of the power seat lifter motor assembly LH and front seat adjuster assembly LH.



Hide 85822B 10.REMOVE POWER SEAT TILT MOTOR ASSEMBLY LH

a.
B526567

Disconnect the connector.


b.

Detach the clamp.


c.
B526568

Remove the 3 bolts and power seat tilt motor assembly LH.

NOTICE:

Do not damage or dirty the gears of the power seat tilt motor assembly LH and front seat adjuster assembly LH.