Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
72057
1.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (for RH Side)
Attach the hook and install the rear seat lock control lever sub-assembly RH to the rear seatback lock assembly RH.
72630C
2.INSTALL REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)
Install the rear seatback lock assembly RH with the 3 bolts.
Install the 2 screws.
73350C
3.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)
87510R
4.INSTALL REAR SEATBACK HEATER ASSEMBLY RH (for RH Side, w/ Seat Heater System)
71077S
5.INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)
When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Attach the hook to install the separate type rear seatback cover RH to the separate type rear seatback pad RH.
Be careful not to dirty or damage the separate type rear seatback cover.
6.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Set the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH.
Pass the rear center seat outer belt assembly through the hole of separate type rear seatback cover with pad.
Attach the hook.
Attach the claw and install the 4 rear seat headrest supports.
72830
7.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (for RH Side)
Install the bush.
| *a | Outside Location Pin |
| *b | Inside Location Pin |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the inside location pin in the installation direction (1) shown in the illustration.
Attach the outside location pin in the installation direction (2) shown in the illustration.
Fold the rear center seat armrest assembly forward.
Install the rear center seat armrest assembly with the washer and bolt.
72868B
8.INSTALL CENTER ARMREST HINGE COVER (for RH Side)
|
Install in this Direction |
Attach the guide and claw to install the center armrest hinge cover.
71701B
9.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH (for RH Side)
| *a | Guide |
| *b | Hook |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) |
Attach the hook in the installation direction (1) shown in the illustration.
Attach the guide in the installation direction (2) shown in the illustration.
Attach the claw in the installation direction (3) shown in the illustration.
Install the rear seatback board sub-assembly RH with the 2 clips.
Close the 2 fasteners.
Put the 2 fasteners in the hole of rear seatback board sub-assembly RH.
Attach the hook.
Attach the hook.
72667A
10.INSTALL REAR UPPER SEATBACK LOCK BEZEL RH (for RH Side)
|
Install in this Direction |
Attach the claw and install the rear upper seatback lock bezel RH.
72668E
11.INSTALL REAR LOWER SEATBACK LOCK BEZEL RH (for RH Side)
|
Install in this Direction |
Attach the guide and claw to install the rear lower seatback lock bezel RH.
73178A
12.INSTALL SEAT BELT ANCHOR COVER CAP (for RH Side)
Pass the rear center seat outer belt assembly from the slit of rear seat shoulder belt cover.
|
Install in this Direction |
Attach the guide to install the seat belt anchor cover cap as shown in the illustration.
73373
13.INSTALL REAR SEAT SHOULDER BELT COVER (for RH Side)
|
Install in this Direction |
Attach the guide and claw to install the rear seat shoulder belt cover.
72058A
14.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (for LH Side)
Attach the hook and install the rear seat lock control lever sub-assembly LH to the rear seatback lock assembly LH.
72640A
15.INSTALL REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)
Install the rear seatback lock assembly LH with the 3 bolts.
Install the 2 screws.
87510S
16.INSTALL REAR SEATBACK HEATER ASSEMBLY LH (for LH Side, w/ Seat Heater System)
71078S
17.INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)
When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Attach the hook to install the separate type rear seatback cover LH to the separate type rear seatback pad LH.
Be careful not to dirty or damage the separate type rear seatback cover.
18.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Set the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
Attach the claw and install the 2 rear seat headrest supports.
71702B
19.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH (for LH Side)
| *a | Guide |
| *b | Hook |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) |
Attach the hook in the installation direction (1) shown in the illustration.
Attach the guide in the installation direction (2) shown in the illustration.
Attach the claw in the installation direction (3) shown in the illustration.
Install the rear seatback board sub-assembly LH with the 2 clips.
Install the clip.
Close the 2 fasteners.
Put the 2 fasteners in the hole of rear seatback board sub-assembly LH.
Attach the hook.
Attach the hook.
72667B
20.INSTALL REAR UPPER SEATBACK LOCK BEZEL LH (for LH Side)
|
Install in this Direction |
Attach the claw and install the rear upper seatback lock bezel LH.
72668F
21.INSTALL REAR LOWER SEATBACK LOCK BEZEL LH (for LH Side)
|
Install in this Direction |
Attach the guide and claw to install the rear lower seatback lock bezel LH.
71960B
22.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
Install the rear center seat headrest assembly.
71940A
23.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the 2 rear seat headrest assemblies.
82194
24.INSTALL REAR SEAT WIRE LH (w/ Occupant Detection Sensor)
Attach the clamp and install the rear seat wire LH.
82193
25.INSTALL REAR SEAT WIRE RH (w/ Occupant Detection Sensor)
Attach the clamp and install the rear seat wire RH.
87510Q
26.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
87510P
27.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
Use the same procedure described for the LH side.
71075B
28.INSTALL BENCH TYPE REAR SEAT CUSHION COVER
When installing a bench type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Attach the hook to install the bench type rear seat cushion cover to the rear seat cushion pad.
Be careful not to dirty or damage the bench type rear seat cushion cover.
w/ Occupant Detection Sensor:
Attach the clamp and claw.
Connect the 3 connectors.
Attach the hook.
for Gasoline Model:
for HV Model: