This DTC is stored when the telephone transceiver assembly detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.
If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.
If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1571 | Green LED Error | Current for the manual (SOS) switch indicator (green) exceeds malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telephone transceiver assembly ·
Map light sub-assembly (manual (SOS) switch) ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
When replacing the telephone transceiver assembly, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds.
Turn the GTS on.
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component with harness connected
(Map Light Sub-assembly (Manual (SOS) Switch)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-19 (IND2) - P14-12 (GND3) | 2 seconds after ignition switch turned to ON
→ Ignition switch off |
8.5 to 10 V
→ Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Sub-assembly (Manual (SOS) Switch)) |
Remove the map light sub-assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from batteries to terminal 19 (IND2) and a negative (-) lead to terminal 12 (GND3) of the map light sub-assembly (manual (SOS) switch) connector.
Check if the manual (SOS) switch indicator (green) comes on.
Manual (SOS) switch indicator (green) illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6 telephone transceiver assembly connector.
Disconnect the P14 map light sub-assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-12 (IND2) - P14-19 (IND2) | Always | Below 1 Ω |
| H6-12 (IND2) or P14-19 (IND2) - Body ground | Always | 10 kΩ or higher |
| H6-26 (SIG-) - P14-12 (GND3) | Always | Below 1 Ω |
| H6-26 (SIG-) or P14-12 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT