Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › 2018.10–2019.09
RM3620E _56 Audio / Visual / Telematics _076049 TELEMATICS _0372098 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a communication telematics box signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON
·

Telephone transceiver assembly

·

Communication telematics box*1

·

Telephone Micro phone Assembly*2

·

Harness or connector

·

Mayday wire*1

·

Map light sub-assembly



*1: w/ Communication telematics box

*2: w/o Communication telematics box

WIRING DIAGRAM

E405960E03
0.906,1.406 1.521,1.604 0.615,0.198 10 false MCMD 1.052,1.813 1.667,2.01 0.615,0.198 10 false SP+ 1.063,2.219 1.677,2.417 0.615,0.198 10 false SP- 0.99,2.594 1.604,2.792 0.615,0.198 10 false MICV 0.938,3.375 1.552,3.573 0.615,0.198 10 false MIC1+ 0.917,2.958 1.531,3.156 0.615,0.198 10 false MIC2+ 1.042,3.792 1.656,3.99 0.615,0.198 10 false MCI- 5.667,1.396 6.281,1.594 0.615,0.198 10 false MCMD 5.667,1.781 6.281,1.979 0.615,0.198 10 false SP+ 5.667,2.198 6.281,2.396 0.615,0.198 10 false SP- 5.656,2.583 6.271,2.781 0.615,0.198 10 false MICV 5.646,3 6.26,3.198 0.615,0.198 10 false MCVD 5.656,3.365 6.271,3.563 0.615,0.198 10 false MCI+ 5.656,3.771 6.271,3.969 0.615,0.198 10 false MCI- 5.531,4.792 6.927,5.469 1.396,0.677 10 false Telephone Transceiver Assembly 4.031,3.99 4.688,4.219 0.656,0.229 10 false * 0.375,4.75 1.438,5.156 1.063,0.406 10 false Communication Telematics Box 0.375,4.583 1.146,4.99 0.771,0.406 10 false P 2.104,1.302 2.719,1.5 0.615,0.198 10 false MCMD 2.26,1.698 2.875,1.896 0.615,0.198 10 false SP+ 2.302,2.104 2.917,2.302 0.615,0.198 10 false SP- 2.198,2.479 2.813,2.677 0.615,0.198 10 false MICV 2.219,3.302 2.833,3.5 0.615,0.198 10 false MIC2 2.219,2.906 2.833,3.104 0.615,0.198 10 false MIC1 2.229,3.677 2.844,3.875 0.615,0.198 10 false MCI- 1.458,1.313 2.073,1.51 0.615,0.198 10 false 1 1.479,1.708 2.094,1.906 0.615,0.198 10 false 3 1.469,2.104 2.083,2.302 0.615,0.198 10 false 8 1.479,2.5 2.094,2.698 0.615,0.198 10 false 5 1.5,3.292 2.115,3.49 0.615,0.198 10 false 2 1.5,2.896 2.115,3.094 0.615,0.198 10 false 7 1.49,3.677 2.104,3.875 0.615,0.198 10 false 4 2.76,1.219 3.375,1.417 0.615,0.198 10 false 1 2.76,1.615 3.375,1.813 0.615,0.198 10 false 3 2.76,2 3.375,2.198 0.615,0.198 10 false 9 2.792,2.406 3.406,2.604 0.615,0.198 10 false 6 2.74,3.208 3.354,3.406 0.615,0.198 10 false 10 2.76,2.802 3.375,3 0.615,0.198 10 false 11 2.771,3.594 3.385,3.792 0.615,0.198 10 false 5 5.344,1.677 5.958,1.875 0.615,0.198 10 false 20 5.333,1.292 5.948,1.49 0.615,0.198 10 false 14 5.354,2.073 5.969,2.271 0.615,0.198 10 false 21 5.354,2.458 5.969,2.656 0.615,0.198 10 false 31 5.354,2.865 5.979,3.063 0.625,0.198 10 false 33 5.344,3.656 5.969,3.854 0.625,0.198 10 false 35 5.531,4.604 6.302,5.01 0.771,0.406 10 false H6 2.688,1.406 3.458,1.813 0.771,0.406 10 false P18 5.646,4.198 6.26,4.396 0.615,0.198 10 false SGND 5.354,4.083 5.979,4.281 0.625,0.198 10 false 32 1.667,4.615 2.781,5.094 1.115,0.479 10 false Mayday Wire 2.688,1.781 3.458,2.188 0.771,0.406 10 false P18 2.698,2.198 3.469,2.604 0.771,0.406 10 false P18 2.719,2.583 3.49,2.99 0.771,0.406 10 false P18 2.688,2.979 3.458,3.385 0.771,0.406 10 false P18 2.698,3.375 3.469,3.781 0.771,0.406 10 false P18 2.688,3.771 3.458,4.177 0.771,0.406 10 false P18 5.365,3.26 5.99,3.458 0.625,0.198 10 false 34 0.177,0.156 5.865,0.396 5.688,0.24 12 false w/ Communication Telematics Box: 0.344,5.458 2.521,5.781 2.177,0.323 10 false *: Shielded

E384839E12
0.729,0.854 1.26,1.063 0.531,0.208 10 false MACC 0.813,1.323 1.271,1.531 0.458,0.208 10 false MIC+ 0.823,1.802 1.281,2.01 0.458,0.208 10 false MIC- 0.292,2.229 1.698,2.604 1.406,0.375 10 false Telephone Microphone Assembly 1.313,0.76 1.469,0.958 0.156,0.198 10 false 5 1.313,1.24 1.469,1.438 0.156,0.198 10 false 3 1.313,1.708 1.469,1.906 0.156,0.198 10 false 2 2.063,0.75 2.219,0.948 0.156,0.198 10 false 7 2.073,1.219 2.229,1.417 0.156,0.198 10 false 6 2.073,1.708 2.229,1.906 0.156,0.198 10 false 5 1.521,0.76 2.052,0.969 0.531,0.208 10 false MACC 1.531,1.25 2.063,1.458 0.531,0.208 10 false MCO+ 1.542,1.719 2.073,1.927 0.531,0.208 10 false MCO- 0.396,3.146 0.896,3.417 0.5,0.271 10 false P14 0.406,3.313 2.167,3.656 1.76,0.344 10 false Map Light Sub-assembly 5.604,0.76 5.844,0.958 0.24,0.198 10 false 33 5.615,1.24 5.854,1.438 0.24,0.198 10 false 34 5.615,1.719 5.854,1.917 0.24,0.198 10 false 35 5.615,2.292 5.854,2.49 0.24,0.198 10 false 32 5.938,0.833 6.469,1.042 0.531,0.208 10 false MCVD 5.917,1.323 6.448,1.531 0.531,0.208 10 false MCI+ 5.927,2.385 6.458,2.594 0.531,0.208 10 false SGND 5.917,1.792 6.448,2 0.531,0.208 10 false MCI- 5.521,2.76 5.823,2.948 0.302,0.188 10 false H6 5.51,2.927 6.906,3.625 1.396,0.698 10 false Telephone Transceiver Assembly 3.781,2.323 3.938,2.49 0.156,0.167 10 false * 2.49,3.344 3.552,3.573 1.063,0.229 10 false *: Shielded 0.167,0.125 6.042,0.365 5.875,0.24 12 false w/o Communication Telematics Box:

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.


e.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

f.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/ Communication Telematics Box) B
NG (w/o Communication Telematics Box) C



A

B

2.CHECK TELEPHONE TRANSCEIVER ASSEMBLY

C

7.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
2.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
B518361C08
1.479,0.135 1.896,0.365 0.417,0.229 1.385,1.833 1.604,1.313 true 0.823,1.615 1.26,1.313 true 0.083,0.094 0.438,0.385 0.354,0.292 10 false *a 0.531,1.635 1.063,1.875 0.531,0.24 10 false MCI- 1.031,1.865 1.563,2.104 0.531,0.24 10 false MICV 1.594,0.177 2.125,0.417 0.531,0.24 10 false H6
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-31 (MICV) - Body ground Ignition switch ACC 4 to 6 V


Standard Resistance:
Tester Connection Condition Specified Condition
H6-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)

NG

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAYDAY WIRE)
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the P18 mayday wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-14 (MCMD) - P18-1 (MCMD) Always Below 1 Ω
H6-20 (SP+) - P18-3 (SP+) Always Below 1 Ω
H6-21 (SP-) - P18-9 (SP-) Always Below 1 Ω
H6-31 (MICV) - P18-6 (MICV) Always Below 1 Ω
H6-33 (MCVD) - P18-11 (MIC1) Always Below 1 Ω
H6-34 (MCI+) - P18-10 (MIC2) Always Below 1 Ω
H6-35 (MCI-) - P18-5 (MCI-) Always Below 1 Ω
H6-14 (MCMD) or P18-1 (MCMD) - Body ground Always 10 kΩ or higher
H6-20 (SP+) or P18-3 (SP+) - Body ground Always 10 kΩ or higher
H6-21 (SP-) or P18-9 (SP-) - Body ground Always 10 kΩ or higher
H6-31 (MICV) or P18-6 (MICV) - Body ground Always 10 kΩ or higher
H6-33 (MCVD) or P18-11 (MIC1) - Body ground Always 10 kΩ or higher
H6-34 (MCI+) or P18-10 (MIC2) - Body ground Always 10 kΩ or higher
H6-35 (MCI-) or P18-5 (MCI-) - Body ground Always 10 kΩ or higher
H6-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAYDAY WIRE (COMMUNICATION TELEMATICS BOX - WIRE HARNESS)
a.

Disconnect the P18 wire harness connector.


b.

Disconnect the P communication telematics box connector.


c.
E409641C01
1.49,2.823 1.865,3.083 0.375,0.26 1.521,0.365 1.896,0.625 0.375,0.26 2.177,1.281 2.646,1.281 true 1.313,3.208 1.708,3.729 true 1.823,1.271 2.542,0.708 true 1.823,1.604 2.479,2.031 true 0.781,1.292 1.208,1.292 true 1.583,1.615 0.938,2.177 true 1.385,1.583 0.906,1.792 true 1.406,1.219 0.896,0.917 true 1,3.396 1.49,3.729 true 0.917,3.771 1.302,3.771 true 1.719,4 1.854,4.365 true 2.25,3.292 1.917,3.719 true 1.313,4.333 1.531,3.979 true 2.5,3.76 2.073,3.76 true 0.365,2.635 0.677,2.833 0.313,0.198 10 false *b 0.292,0.26 0.604,0.458 0.313,0.198 10 false *a 1.646,2.865 1.958,3.063 0.313,0.198 10 false P 1.583,0.417 1.896,0.615 0.313,0.198 10 false P18 2.688,1.208 3.271,1.583 0.583,0.375 10 false MCMD 0.448,3.688 1.031,4.063 0.583,0.375 10 false MCMD 2.583,0.625 3.167,1 0.583,0.375 10 false SP+ 2.531,1.969 3.115,2.344 0.583,0.375 10 false SP- 0.417,1.219 1,1.594 0.583,0.375 10 false MICV 0.594,2.104 1.094,2.458 0.5,0.354 10 false MIC2 0.563,0.823 1.146,1.198 0.583,0.375 10 false MCI- 0.552,1.719 1.135,2.094 0.583,0.375 10 false MIC1 1.063,3.063 1.646,3.438 0.583,0.375 10 false SP+ 0.563,3.313 1.146,3.688 0.583,0.375 10 false MIC1+ 1.896,4.323 2.531,4.656 0.635,0.333 10 false SP- 2.542,3.698 3.125,4.073 0.583,0.375 10 false MICV 0.927,4.313 1.427,4.667 0.5,0.354 10 false MIC2+ 2.229,3.135 2.813,3.51 0.583,0.375 10 false MCI-
*a Component without harness connected
(Wire Harness)
*b Component without harness connected
(Communication Telematics Box)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P18-1 (MCMD) - P-1 (MCMD) Always Below 1 Ω
P18-3 (SP+) - P-3 (SP+) Always Below 1 Ω
P18-9 (SP-) - P-8 (SP-) Always Below 1 Ω
P18-6 (MICV) - P-5 (MICV) Always Below 1 Ω
P18-10 (MIC2) - P-2 (MIC1+) Always Below 1 Ω
P18-11 (MIC1) - P-7 (MIC2+) Always Below 1 Ω
P18-5 (MCI-) - P-4 (MCI-) Always Below 1 Ω
P18-1 (MCMD) or P-1 (MCMD) - Body ground Always 10 kΩ or higher
P18-3 (SP+) or P-3 (SP+) - Body ground Always 10 kΩ or higher
P18-9 (SP-) or P-8 (SP-) - Body ground Always 10 kΩ or higher
P18-6 (MICV) or P-5 (MICV) - Body ground Always 10 kΩ or higher
P18-10 (MIC2) or P-2 (MIC1+) - Body ground Always 10 kΩ or higher
P18-11 (MIC1) or P-7 (MIC2+) - Body ground Always 10 kΩ or higher
P18-5 (MCI-) or P-4 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMUNICATION TELEMATICS BOX

NG

5.REPLACE COMMUNICATION TELEMATICS BOX
a.

Replace the communication telematics box with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION TELEMATICS BOX IS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

6.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.
B518361C09
1.479,0.135 1.896,0.365 0.417,0.229 1.385,1.833 1.448,1.323 true 0.083,0.094 0.438,0.385 0.354,0.292 10 false *a 1.031,1.865 1.563,2.104 0.531,0.24 10 false MCVD 1.594,0.177 2.125,0.417 0.531,0.24 10 false H6
*a Component with harness connected
(Telephone Transceiver Assembly)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

12.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - MAP LIGHT SUB-ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the H6 telephone transceiver assembly connector.


b.

Disconnect the P14 map light sub-assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-33 (MCVD) - P14-7 (MACC) Always Below 1 Ω
H6-34 (MCI+) - P14-6 (MCO+) Always Below 1 Ω
H6-35 (MCI-) - P14-5 (MCO-) Always Below 1 Ω
H6-33 (MCVD) or P14-7 (MACC) - Body ground Always 10 kΩ or higher
H6-34 (MCI+) or P14-6 (MCO+) - Body ground Always 10 kΩ or higher
H6-35 (MCI-) or P14-5 (MCO-) - Body ground Always 10 kΩ or higher
H6-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT MAP LIGHT SUB-ASSEMBLY
a.

Remove the map light sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


c.
E405964C01
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 1.448,0.948 1.208,0.188 1.208,0.188 1.385,0.188 true 1.635,0.948 1.99,0.208 1.99,0.208 2.167,0.208 true 2.271,2.792 2.417,3.01 2.417,3.01 2.573,3.01 true 1.76,2.771 2.125,3.198 2.125,3.198 2.302,3.198 true 1.802,0.948 2.688,0.427 2.688,0.427 2.865,0.427 true 1.448,2.781 1.521,3.24 1.521,3.24 1.698,3.24 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.24,0.906 0.448,1.125 0.208,0.219 10 false A 0.49,2.458 0.698,2.677 0.208,0.219 10 false B 2.615,2.927 3.052,3.135 0.438,0.208 10 false MACC 1.438,0.125 1.875,0.333 0.438,0.208 10 false MACC 2.198,0.125 2.677,0.344 0.479,0.219 10 false MCO+ 2.896,0.365 3.375,0.583 0.479,0.219 10 false MCO- 2.344,3.115 2.823,3.333 0.479,0.219 10 false MIC+ 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC-
*a Component without harness connected
(Map Light Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-7 (MACC) - B-5 (MACC) Always Below 1 Ω
A-6 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-5 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-7 (MACC) - A-6 (MCO+) Always 10 kΩ or higher
A-7 (MACC) - A-5 (MCO-) Always 10 kΩ or higher
A-6 (MCO+) - A-5 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT SUB-ASSEMBLY

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT