This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U117787 | Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 100 junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor RH (A) ·
Power source circuit of blind spot monitor sensor RH (A) ·
Blind spot monitor sensor RH (A) ground circuit ·
Blind spot monitor sensor LH (B) |
| U117887 | Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 100 junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH (B) ·
Power source circuit of blind spot monitor sensor LH (B) ·
Blind spot monitor sensor LH (B) ground circuit ·
Blind spot monitor sensor RH (A) |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 only is output | A |
| DTC U117887 only is output | B |
| DTC U117787 and U117887 are output | C |
A
B
C
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-10 (BRGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q13-5 (BRB) - Body ground | Power switch on (IG) | 11 to 14 V |
| Q13-5 (BRB) - Body ground | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-10 (BLGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q1-5 (BLB) - Body ground | Power switch on (IG) | 11 to 14 V |
| Q1-5 (BLB) - Body ground | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(No. 100 CAN Junction Connector) |
| *b | Front view of DLC3 |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| M30-5 (CANH) - M30-16 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| M30-5 (CANH) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| M30-16 (CANL) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| M30-5 (CANH) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| M30-16 (CANL) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| Open circuit in CAN main bus lines | B |
| Short circuit between bus lines | C |
·
Short to ground ·
+B short |
D |
A
B
C
D
Reconnect the cable to the negative (-) auxiliary battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 and U117887 are not output | A |
| DTC U117787 and U117887 are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
Disconnect the No. 100 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 100 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly CAN Wire |
| *c | to Blind Spot Monitor Sensor RH (A) CAN Main Wire | *d | to Blind Spot Monitor Sensor LH (B) CAN Main Wire |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M30-5 (CANH) - M30-16 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-6 (CANH) - M30-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| M30-7 (CANH) - M30-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-1 (CA2P) - Q1-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-1 (CA2P) - Q13-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-37 (CANH) - H4-38 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
NG
Disconnect the No. 100 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 100 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly CAN Wire |
| *c | to Blind Spot Monitor Sensor RH (A) CAN Main Wire | *d | to Blind Spot Monitor Sensor LH (B) CAN Main Wire |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M30-5 (CANH) - M30-16 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-6 (CANH) - M30-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| M30-7 (CANH) - M30-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-1 (CA2P) - Q1-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-1 (CA2P) - Q13-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-37 (CANH) - H4-38 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
NG
Disconnect the No. 100 junction connector.
| *a | Front view of wire harness connector
(to No. 100 CAN Junction Connector) |
*b | Front view of DLC3 |
| *c | to Clearance Warning ECU Assembly CAN Wire | *d | to Blind Spot Monitor Sensor RH (A) CAN Main Wire |
| *e | to Blind Spot Monitor Sensor LH (B) CAN Main Wire | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M30-5 (CANH) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-16 (CANL) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-5 (CANH) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M30-16 (CANL) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M30-6 (CANH) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-17 (CANL) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-6 (CANH) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M30-17 (CANL) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M30-7 (CANH) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-18 (CANL) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M30-7 (CANH) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M30-18 (CANL) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
Check for short that was confirmed to be a malfunction by confirming symptoms.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B)) |
| *b | Front view of DLC3 |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q1-1 (CA2P) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q1-6 (CA2N) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q1-1 (CA2P) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Q1-6 (CA2N) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A)) |
| *b | Front view of DLC3 |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q13-1 (CA2P) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q13-6 (CA2N) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| Q13-1 (CA2P) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Q13-6 (CA2N) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
| *b | Front view of DLC3 |
Reconnect the M30 No. 100 CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H4-37 (CANH) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-38 (CANL) - G114-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| H4-37 (CANH) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| H4-38 (CANL) - G114-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
NG