Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (for HV Model with Parking Support Brake System)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370836 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for HV Model with Parking Support Brake System) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for HV Model with Parking Support Brake System)  No. 2 Clearance Warning Buzzer Circuit  


DESCRIPTION

This circuit consists of the No. 2 clearance warning buzzer and clearance warning ECU assembly. An ECU-excited type buzzer is used. The ECU operates the buzzers using a sound pattern that changes depending on the distance to the obstacle.

WIRING DIAGRAM

E240924E78
5.5,1.906 6.677,2.375 1.177,0.469 10 false Clearance Warning ECU Assembly 5.5,1.74 5.958,1.938 0.458,0.198 10 false H4 1.083,1.75 2.125,2.292 1.042,0.542 10 false No. 2 Clearance Warning Buzzer 1.094,1.594 1.552,1.854 0.458,0.26 10 false M13 5.292,0.365 5.75,0.563 0.458,0.198 10 false 25 5.271,1.156 5.729,1.354 0.458,0.198 10 false 26 2.063,1.156 2.521,1.354 0.458,0.198 10 false 2 2.042,0.365 2.5,0.563 0.458,0.198 10 false 1 5.583,1.271 6.042,1.469 0.458,0.198 10 false ER 5.563,0.479 6.021,0.677 0.458,0.198 10 false BBZ 1.719,0.458 2.177,0.719 0.458,0.26 10 false Z+ 1.719,1.26 2.177,1.521 0.458,0.26 10 false Z-

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer OFF or ON Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - NO. 2 CLEARANCE WARNING BUZZER)
a.

Disconnect the H4 clearance warning ECU assembly connector.


b.

Disconnect the M13 No. 2 clearance warning buzzer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-25 (BBZ) - M13-1 (Z+) Always Below 1 Ω
H4-26 (ER) - M13-2 (Z-) Always Below 1 Ω
H4-25 (BBZ) or M13-1 (Z+) - Body ground Always 10 kΩ or higher
H4-26 (ER) or M13-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 2 CLEARANCE WARNING BUZZER
a.

Replace the No. 2 clearance warning buzzer with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING BUZZER (for Rear Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Warning / Active Test.


e.

Check that the buzzer operates by performing the Active Test.

Body Electrical > Clearance Warning > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Buzzer No. 2 clearance warning buzzer OFF or ON Confirm that the vehicle is stopped and the power switch is on (IG)
Body Electrical > Clearance Warning > Active Test
Tester Display
Rear Buzzer
50004 438 2
OK:

The No. 2 clearance warning buzzer sounds.


Result:
Proceed to
OK
NG




OK

END (NO. 2 CLEARANCE WARNING BUZZER WAS DEFECTIVE)

NG