Home › Engine / Hybrid System › A25A-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD
RM3620E _51 Engine / Hybrid System _076480 A25A-FKS INTAKE / EXHAUST _0372146 INTAKE MANIFOLD A

A25A-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL VACUUM HOSE

a.

Install the vacuum hose to the intake manifold.


Hide 12611B 2.INSTALL NO. 1 ENGINE COVER

a.

Install the No. 1 engine cover with the clip.


Hide 17177 3.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 4.INSTALL INTAKE MANIFOLD

a.
A402245N01
1.458,0.063 1.615,0.26 0.156,0.198 10 true 1 0.844,0.031 0.979,0.208 0.135,0.177 10 true 2 2.115,0.021 2.25,0.198 0.135,0.177 10 true 3 0.229,0.125 0.365,0.302 0.135,0.177 10 true 4 2.75,0.042 2.885,0.219 0.135,0.177 10 true 5

w/o Stud Bolt:

i.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 5 bolts.


ii.

Tighten the 5 bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



b.
A436535C02
1.49,0.052 1.646,0.25 0.156,0.198 10 true 1 0.99,0.042 1.146,0.24 0.156,0.198 10 true 2 2.229,0.042 2.385,0.24 0.156,0.198 10 true 3 0.219,0.094 0.375,0.292 0.156,0.198 10 true 4 2.771,0.031 2.927,0.229 0.156,0.198 10 true 5
V100135

Bolt
V100136

Nut


w/ Stud Bolt:

i.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 3 bolts and 2 nuts.


ii.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)



Hide 23820 5.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.

Connect the No. 2 fuel vapor feed hose to the intake manifold.


Hide 16279 6.CONNECT NO. 3 WATER BY-PASS PIPE

a.

Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 5 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 16278 7.INSTALL NO. 2 WATER BY-PASS PIPE

a.
A402242N01
0.896,1.802 1.052,2 0.156,0.198 10 true A 1.51,1.927 1.698,2.094 0.188,0.167 10 true B 0.802,0.302 0.958,0.5 0.156,0.198 10 true A

Temporarily install the No. 2 water by-pass pipe to the cylinder block sub-assembly with the bolt (B).


b.

Using an 8 mm socket wrench, temporarily install the No. 2 water by-pass pipe to the intake manifold with the 2 bolts (A).


c.

Tighten the bolt (B).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Using the 8 mm socket wrench, tighten the 2 bolts (A).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 8.CONNECT ENGINE WIRE

a.

Attach the wire harness clamp to connect the engine wire.


b.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89421 9.INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 22030 11.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY