Home › Engine / Hybrid System › A25A-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076480 A25A-FKS INTAKE / EXHAUST _0372147 EXHAUST MANIFOLD A

A25A-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 17410 2.REMOVE FRONT EXHAUST PIPE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A432691

Detach the 2 wire harness clamps.


b.

Disconnect the air fuel ratio sensor (for Sensor 2) connector.


c.
A433926

Remove the 2 bolts, 2 nuts and disconnect the front exhaust pipe assembly from the exhaust manifold and tail exhaust pipe assembly.


d.

Remove the front exhaust pipe assembly from the 2 exhaust pipe supports.


e.

Remove the 2 gaskets from the front exhaust pipe assembly.


Hide 89467B 3.REMOVE AIR FUEL RATIO SENSOR (for Sensor 1)

Hide 4.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A402258

Remove the bolt and wire harness clamp bracket.


Hide 17167 5.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402259

Remove the 5 bolts and separate the No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 58151 6.SEPARATE NO. 1 UPPER FRONT FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A433924

Remove the 2 nuts and separate the No. 1 upper front floor heat insulator from the vehicle body.


Hide 17118 7.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A401948

Remove the bolt, nut and manifold stay from the exhaust manifold and cylinder block sub-assembly.


Hide 17141 8.REMOVE EXHAUST MANIFOLD

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A402260

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.


b.

Remove the No. 1 exhaust manifold heat insulator, No. 1 upper front floor heat insulator and exhaust manifold.


c.
A402262

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 9.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402265

Remove the 6 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold.