Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM(for HV Model)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370839 PANORAMIC VIEW MONITOR SYSTEM(for HV Model) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(for HV Model)  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the Signal Check screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>DIAGNOSIS SYSTEM

HINT:
·

On the Signal Check screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the Signal Check screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch signal input state DTC is not output Panoramic view monitor switch
MIRROR SW* Vehicle wire harness Outer rear view mirror assembly signal input state DTC is not output Outer rear view mirror assembly

*: w/ Retract Mirror (w/o Auto Power Retract Mirror)


WIRING DIAGRAM

E407123E01
5.073,2.896 6.5,3.104 1.427,0.208 10 false Parking Assist ECU 5.146,1.76 5.896,1.979 0.75,0.219 10 false BLSW 2.052,2.229 4.135,2.5 2.083,0.271 10 false Panoramic View Monitor Switch 2.042,2.063 2.323,2.313 0.281,0.25 10 false G37 0.885,3.323 2.979,3.531 2.094,0.208 10 false : CAN Communication Line 5.063,2.708 5.344,2.958 0.281,0.25 10 false N25 4.833,1.635 5.104,1.854 0.271,0.219 10 false 15 3.594,1.635 3.865,1.854 0.271,0.219 10 false 5 2.177,1.646 2.448,1.865 0.271,0.219 10 false 2 3.344,1.646 3.615,1.865 0.271,0.219 10 false D 2.438,1.646 2.708,1.865 0.271,0.219 10 false E 0.26,2.969 4.073,3.219 3.813,0.25 10 false *: w/ Retract Mirror (w/o Auto Power Retract Mirror) 5.146,1.125 5.896,1.344 0.75,0.219 10 false MPOS* 4.823,1.031 5.094,1.25 0.271,0.219 10 false 16 0.344,1.688 1.771,2.042 1.427,0.354 10 false Outer Rear View Mirror Assembly LH 0.344,1.531 0.625,1.781 0.281,0.25 10 false J13 1.313,1.146 2.063,1.365 0.75,0.219 10 false MF* 1.823,1.021 2.094,1.24 0.271,0.219 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the auxiliary battery cable is disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM(for HV Model)>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E407133C01
1.885,1.063 2.198,1.219 0.313,0.156 10 false *A 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a
*A w/ Retract Mirror (w/o Auto Power Retract Mirror)
*a Example


Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B
"MIRROR SW" displays "CHK" (red) (w/ Retract Mirror (w/o Auto Power Retract Mirror)) C



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)

B

C

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - PARKING ASSIST ECU)
2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the G37 panoramic view monitor switch connector.


b.

Disconnect the N25 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-5 (D) - N25-15 (BLSW) Always Below 1 Ω
G37-2 (E) - Body ground Always Below 1 Ω
G37-5 (D) or N25-15 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PANORAMIC VIEW MONITOR SWITCH
a.

Remove the panoramic view monitor switch.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>COMBINATION SWITCH>REMOVAL



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - PARKING ASSIST ECU)
a.

Disconnect the J13 outer rear view mirror assembly LH connector.


b.

Disconnect the N25 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-5 (MF) - N25-16 (MPOS) Always Below 1 Ω
J13-5 (MF) or N25-16 (MPOS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR