Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › EMISSION CONTROL SYSTEM (w/o Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076502 A25A-FKS EMISSION CONTROL _0372395 EMISSION CONTROL SYSTEM(w/o Canister Pump Module) G

A25A-FKS EMISSION CONTROL  EMISSION CONTROL SYSTEM(w/o Canister Pump Module)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL CUT OPERATION

a.

Start the engine.


b.

Warm up the engine.


c.

Increase the engine speed to approximately 3500 rpm.


d.
A401951C01
1.625,1.521 2.125,1.521 true 1.771,0.76 2.271,0.76 true 2.104,1.417 2.344,1.625 0.24,0.208 10 true *1 2.26,0.656 2.49,0.865 0.229,0.208 10 true *a
*1 Fuel Injector Assembly
*a Sound Scope


Use a sound scope to check for fuel injector assembly operating sounds.


e.

When the accelerator pedal is fully released, check that fuel injector assembly operating sounds stop momentarily and then resume.

Standard:
Item Specified Condition
Fuel cut permission engine speed 2500 rpm or higher
Fuel injection restart engine speed 1400 rpm


If the result is not as specified, check the fuel injector assemblies, wire harness and ECM.


Hide 2.VISUALLY CHECK HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil level dipstick, oil filler cap sub-assembly, ventilation hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in any part of the air induction system between the throttle body with motor assembly and cylinder head sub-assembly will cause engine failure or engine malfunctions.



If any defects are found, replace parts as necessary.


Hide 3.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.
A413940

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

f.

Check that vacuum occurs at the purge valve (purge VSV) port.


g.

If vacuum does not occur, check the following items.

·

Purge valve (purge VSV)

·

Clogging in the No. 2 fuel vapor feed hose that connects the intake manifold and purge valve (purge VSV)



h.

Exit Active Test mode and connect the No. 1 fuel vapor feed hose assembly to the purge valve (purge VSV) and slide the clip to secure it.

Click hereEngine / Hybrid System>A25A-FKS (EMISSION CONTROL)>PURGE VALVE(w/o Canister Pump Module)>INSTALLATION

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.


i.

Enter the following menus: Powertrain / Engine / Data List / EVAP (Purge) VSV.

Powertrain > Engine > Data List
Tester Display
EVAP (Purge) VSV
50003 372 226

j.

Warm up the engine and drive the vehicle.


k.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.