Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › CANISTER(w/ Canister Pump Module)
RM3620E _51 Engine / Hybrid System _076502 A25A-FKS EMISSION CONTROL _0372399 CANISTER(w/ Canister Pump Module) A

A25A-FKS EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 77740 2.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.

Detach the clamp and disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

A433190C01
1.323,1.073 1.771,1.073 true 1.646,2.344 1.917,2.344 false 0.865,2.156 1.042,2.156 1.042,2.156 1.229,1.958 false 5.26,1.458 4.99,1.073 4.99,1.073 4.813,1.073 false 6.365,1.563 5.958,1.563 false 6.323,2.271 5.917,2.271 false 5.177,2.01 4.771,2.01 false 1.063,1 1.302,1.198 0.24,0.198 10 true *1 6.354,2.188 6.667,2.344 0.313,0.156 10 false *2 1.958,2.24 2.271,2.396 0.313,0.156 10 false *a 0.688,2.063 1,2.219 0.313,0.156 10 false *b 4.656,0.969 4.969,1.125 0.313,0.156 10 false *c 6.406,1.448 6.719,1.604 0.313,0.156 10 false *d 4.583,1.906 4.896,2.063 0.313,0.156 10 false *a
*1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull
V100137

Pull off - -


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the fuel tank vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the fuel tank vent hose.



b.

Disconnect the vent line hose from the canister (charcoal canister assembly).

A433191C01
2.875,1.083 3.677,1.063 true 5.24,1.438 4.885,1.104 4.885,1.104 4.656,1.104 true 4.531,1.979 5.156,1.979 true 3.208,2.313 3.521,2.313 true 2.375,2.25 2.583,2.25 2.583,2.25 2.813,1.979 true 5.948,1.542 6.573,1.542 true 5.896,2.281 6.521,2.281 true 3.719,0.958 4.031,1.115 0.313,0.156 10 false *1 6.563,2.188 6.875,2.344 0.313,0.156 10 false *2 3.542,2.229 3.854,2.385 0.313,0.156 10 false *a 2.167,2.156 2.479,2.313 0.313,0.156 10 false *b 4.479,1 4.792,1.156 0.313,0.156 10 false *c 6.625,1.448 6.938,1.604 0.313,0.156 10 false *d 4.354,1.885 4.667,2.042 0.313,0.156 10 false *a
*1 Vent Line Hose *2 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer *b Tab
*c Tube Connector *d O-ring
V100135

Pinch
V100136

Pull
V100137

Pull off - -


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the vent line hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the vent line hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.



HINT:

Do not remove the retainer.


i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the vent line hose.



c.
A433194

Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).


d.
A433195C01
1.365,1.729 1.521,1.927 0.156,0.198 10 false .
V100135

Bolt
V100136

Clip


Remove the 2 bolts.


e.

Disengage the clip from the canister (charcoal canister assembly).


f.
A433196

Disengage the claw and remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.


g.
A433197

Remove the clip from the vehicle body.


Hide 77730C 3.REMOVE NO. 2 CHARCOAL CANISTER SUB-ASSEMBLY

a.

Disconnect the air line tube from the leak detection pump sub-assembly.

A433755C01
4.844,2.156 5.26,1.74 true 0.844,1.042 0.552,0.823 0.552,0.823 0.313,0.823 true 6.24,1.146 6.458,0.896 6.458,0.896 6.625,0.896 false 5.542,1.729 5.542,2.156 false 5.979,1.875 5.979,2.302 false 0.073,0.74 0.302,1.01 0.229,0.271 10 true *1 6.677,0.792 6.99,0.948 0.313,0.156 10 false *2 4.677,2.104 4.99,2.26 0.313,0.156 10 false *a 5.458,2.188 5.771,2.344 0.313,0.156 10 false *b 5.906,2.323 6.219,2.479 0.313,0.156 10 false *c
*1 Air Line Tube *2 Pipe (Leak Detection Pump Sub-assembly)
*a Tube Connector *b O-ring
*c Retainer - -
V100135

Pinch
V100136

Pull out
V100137

Pull off - -


NOTICE:
·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull to release them.



i.

Push the air line tube firmly toward the leak detection pump sub-assembly.


ii.

Pinch the tube connector as shown in the illustration.


iii.

Pull off the air line tube from the pipe (leak detection pump sub-assembly).



b.
A433200

Disconnect the leak detection pump sub-assembly connector.


c.
A433201

Remove the 3 bolts and No. 2 charcoal canister sub-assembly from the vehicle body.


Hide 77740R 4.REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.

Before removing the leak detection pump sub-assembly, clean the No. 2 charcoal canister sub-assembly by blowing air into it to ensure that the No. 2 charcoal canister sub-assembly is free of foreign matter.

NOTICE:
·

Make sure to clean the No. 2 charcoal canister sub-assembly using air only.

·

Do not use gasoline, thinners or solvents.




b.
A401931C01
1.198,1.76 1.198,2 false 1.125,1.979 1.417,2.167 0.292,0.188 10 false *a
*a Protective Tape


While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.


c.

Check if the No. 2 charcoal canister sub-assembly contains foreign matter such as mud or water.

i.
A377739

Visually check that the inside of the No. 2 charcoal canister sub-assembly is free of foreign matter.


ii.

Hold the No. 2 charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.

If the No. 2 charcoal canister sub-assembly contains foreign matter, replace it.