The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2. DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
77010
4.REMOVE FUEL TANK VENT TUBE ASSEMBLY
77020A
5.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
6.DRAIN FUEL
17430
7.REMOVE TAIL EXHAUST PIPE ASSEMBLY
37110
8.REMOVE PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)
53896B
9.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
53895B
10.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
51441
11.REMOVE NO. 1 ENGINE UNDER COVER
51420
12.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
58166A
13.REMOVE FRONT FLOOR COVER LH
Detach the 3 clips and remove the 2 bolts and 5 screws.
Loosen the 3 nuts and remove the front floor cover LH from the body.
58399D
14.REMOVE NO. 2 FLOOR UNDER COVER
Detach the 3 clips and remove the 2 bolts.
Loosen the 4 nuts and remove the No. 2 floor under cover from the body.
58165C
15.REMOVE FRONT FLOOR COVER RH
Detach the 2 clips and remove the 2 bolts and 4 screws.
Loosen the 3 nuts and remove the front floor cover RH from the body.
58398F
16.REMOVE NO. 1 FLOOR UNDER COVER
Detach the 3 clips and remove the 2 bolts.
Loosen the nut and remove the No. 1 floor under cover from the body.
77606
17.REMOVE NO. 1 FUEL TANK PROTECTOR
Remove the 2 nuts and No. 1 fuel tank protector from the fuel tank band.
18.DISCONNECT FUEL TANK VENT TUBE
Disconnect the fuel tank vent tube from the fuel tank vent hose sub-assembly.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Detach the clamp and disconnect the fuel tank vent tube.
77209C
19.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel tube.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
20.DISCONNECT FUEL TANK BREATHER TUBE
Disconnect the fuel tank breather tube from the fuel tank filler pipe assembly.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
21.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY
Disconnect the fuel tank filler pipe sub-assembly from the fuel tank filler pipe assembly.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
77100
22.REMOVE FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Using an engine lifter, support the fuel tank assembly.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 4 bolts and 2 fuel tank band sub-assemblies.
Lower the engine lifter to remove the fuel tank assembly.
Be careful not to drop the fuel tank assembly.
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
77209C
23.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Detach the clamp and remove the fuel tank main tube sub-assembly from the fuel tank assembly.
77651A
24.REMOVE NO. 1 FUEL TANK CUSHION
Remove the 2 No. 1 fuel tank cushions from the fuel tank assembly.
77606
25.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Detach the 4 clips and remove the No. 1 fuel tank protector sub-assembly from the fuel tank assembly.