Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › 2018.10–2020.05
RM3620E _51 Engine / Hybrid System _076682 M20A-FKS FUEL _0373197 FUEL INJECTOR(for Port Injection) A

M20A-FKS FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 23250F 1.INSTALL PORT FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of spindle oil or gasoline to 4 new O-rings, and install one to each port fuel injector assembly.

NOTICE:

Check that there is no damage or foreign matter on the groove of the port fuel injector assembly when installing the O-ring to each port fuel injector assembly.



b.
A434557C01
1.865,0.969 2.25,1.052 2.25,1.052 2.5,1.052 true 1.833,1.042 2.302,1.333 2.302,1.333 2.552,1.333 true 1.833,0.917 2.302,0.583 2.302,0.583 2.552,0.583 true 2.583,0.49 2.896,0.688 0.313,0.198 10 false *a 2.521,0.948 2.833,1.146 0.313,0.198 10 false *b 2.583,1.229 2.896,1.427 0.313,0.198 10 false *a
*a Claw
*b Stopper


Install the 4 port fuel injector assemblies to the fuel delivery pipe sub-assembly.

NOTICE:
·

Make sure that the port fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the port fuel injector assembly installation holes of the fuel delivery pipe sub-assembly are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the port fuel injector assembly.




Hide 82125N 2.INSTALL NO. 5 ENGINE WIRE

a.

Attach the 2 clamps and install the No. 5 engine wire to the fuel delivery pipe sub-assembly.


b.

Connect the 4 connectors to the 4 port fuel injector assemblies.


Hide 23291A 3.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23891 4.INSTALL FUEL DELIVERY SPACER

a.

Install the 2 fuel delivery spacers to the cylinder head sub-assembly.


Hide 23807 5.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Place the fuel delivery pipe sub-assembly to the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when installing the fuel delivery pipe sub-assembly.



b.

Install the fuel delivery pipe sub-assembly with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


c.

Connect the connector to the fuel delivery pipe sub-assembly.


Hide 23910A 6.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


Hide 89458H 7.INSTALL NO.2 FUEL PRESSURE SENSOR

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 10.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION