Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2018.10–2019.09
RM3620E _59 Vehicle Exterior _076526 SLIDING ROOF / CONVERTIBLE _0372465 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2343  Position Initialization Incomplete  


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2343 Position Initialization Incomplete Sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized Sliding roof ECU (Sliding roof drive gear sub-assembly)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION



HINT:

When DTC B2342 and B2343 are output simultaneously, perform troubleshooting for DTC B2342 first.


PROCEDURE

1.INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION

OK:

Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.



Result:
Proceed to
OK
NG



OK

2.CHECK SLIDING ROOF OPERATION

NG

4.PERFORM ACTIVE TEST USING GTS (Slide Roof)
2.CHECK SLIDING ROOF OPERATION
a.

Check the sliding roof auto operation.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>OPERATION CHECK

OK:

Auto operation operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

3.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Clear DTCs
50002 147

b.

Check for DTCs.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR

Body Electrical > Sliding Roof > Trouble Codes
50001 147
OK:

DTC B2343 is not output.



Result:
Proceed to
OK
NG



OK

END (MALFUNCTION DUE TO INITIALIZATION FAILURE)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

4.PERFORM ACTIVE TEST USING GTS (Slide Roof)
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Sliding Roof > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -
Body Electrical > Sliding Roof > Active Test
Tester Display
Slide Roof
50004 147 1
OK:

Slide roof is operated using GTS.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (Open Switch, Close Switch)

NG

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

5.READ VALUE USING GTS (Open Switch, Close Switch)
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch OPEN switch signal OFF or ON OFF: OPEN switch on the slide switch not pressed
ON: OPEN switch on the slide switch pressed
-
Close Switch CLOSE switch signal OFF or ON OFF: CLOSE switch on the slide switch not pressed
ON: CLOSE switch on the slide switch pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
50003 147 1,4
OK:

The GTS display changes according to switch operation as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

6.INSPECT MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)
6.INSPECT MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)
a.

Remove the map light sub-assembly (slide/tilt switch).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the map light sub-assembly (slide/tilt switch).

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY] - MAP LIGHT SUB-ASSEMBLY [SLIDE/TILT SWITCH] AND BODY GROUND)

NG

REPLACE MAP LIGHT SUB-ASSEMBLY (SLIDE/TILT SWITCH)

7.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY] - MAP LIGHT SUB-ASSEMBLY [SLIDE/TILT SWITCH] AND BODY GROUND)
a.

Disconnect the P14 map light sub-assembly (slide/tilt switch) connector.


b.

Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-5 (UP) - P14-16 (UP) Always Below 1 Ω
P4-8 (CLS) - P14-13 (CLS) Always Below 1 Ω
P4-9 (DWN) - P14-15 (DOWN) Always Below 1 Ω
P4-10 (OPN) - P14-14 (OPN) Always Below 1 Ω
P4-2 (E) - Body ground Always Below 1 Ω
P14-11 (GND) - Body ground Always Below 1 Ω
P4-5 (UP) or P14-16 (UP) - Body ground Always 10 kΩ or higher
P4-8 (CLS) or P14-13 (CLS) - Body ground Always 10 kΩ or higher
P4-9 (DWN) or P14-15 (DOWN) - Body ground Always 10 kΩ or higher
P4-10 (OPN) or P14-14 (OPN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR