Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › THROTTLE BODY
RM3620E _51 Engine / Hybrid System _076384 M20A-FKS ENGINE CONTROL _0372630 THROTTLE BODY A

M20A-FKS ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 3.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A433232

Remove the 2 bolts and inlet air cleaner assembly.


Hide 4.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A433233

Disconnect the mass air flow meter sub-assembly connector.


b.

Detach the 3 wire harness clamps.


c.

w/ Active Control Engine Mount:

i.
A433235C01
2.49,4.302 2.49,3.677 true 2.313,4.302 2.313,3.333 true 2.833,4.292 1.844,4.292 1.844,4.292 1.844,3.917 true 2.875,4.177 3.125,4.385 0.25,0.208 10 false *a
*a Pin


Disconnect the vacuum hose from the air cleaner hose.


ii.

Slide the clip and disconnect the No. 2 PCV hose from the cylinder head cover sub-assembly.


iii.

Loosen the hose clamp and disconnect the air cleaner hose from the throttle body with motor assembly.


iv.

Pull out the air cleaner assembly with air cleaner hose 3 pins from the air cleaner support.



d.

w/o Active Control Engine Mount:

i.
A433234C01
2.323,4.323 2.323,3.333 true 2.5,4.313 2.5,3.688 true 2.917,4.313 1.854,4.313 1.854,4.313 1.854,3.927 true 2.969,4.208 3.219,4.438 0.25,0.229 10 false *a
*a Pin


Slide the clip and disconnect the No. 2 PCV hose from the cylinder head cover sub-assembly.


ii.

Loosen the hose clamp and disconnect the air cleaner hose from the throttle body with motor assembly.


iii.

Pull out the air cleaner assembly with air cleaner hose 3 pins from the air cleaner support.



Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A433236

Disconnect the throttle body with motor assembly connector.


b.

Slide the clip and disconnect the No. 8 water by-pass hose from the throttle body with motor assembly.


c.

Remove the 3 bolts and disconnect the throttle body with motor assembly from the intake manifold.


d.
A433237

Slide the clip and disconnect the No. 5 water by-pass hose to remove the throttle body with motor assembly.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



e.
A433238

Remove the throttle body gasket from the intake manifold.