The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
3. DISCHARGE FUEL SYSTEM PRESSURE
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
6.SECURE STEERING WHEEL
7.REMOVE FRONT WHEELS
53895B
8.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
Remove the 3 screws.
Detach the clip and remove the front fender front splash shield RH.
53896B
9.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
Remove the 3 screws.
Detach the clip and remove the front fender front splash shield LH.
51441
10.REMOVE NO. 1 ENGINE UNDER COVER
Remove the 2 bolts and 10 screws detach the guide and No. 1 engine under cover.
|
Bolt |
|
Screw |
58165C
11.REMOVE FRONT FLOOR COVER RH (w/ Cover)
58166A
12.REMOVE FRONT FLOOR COVER LH (w/ Cover)
58398F
13.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)
58399D
14.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)
51420
15.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
|
Screw |
|
Bolt |
Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.
53737D
16.REMOVE FRONT FENDER APRON SEAL LH
|
Bolt |
|
Clip |
Remove the 2 bolts, clip and front fender apron seal LH.
53736E
17.REMOVE FRONT FENDER APRON SEAL RH
|
Bolt |
|
Clip |
Remove the 2 bolts, clip and front fender apron seal RH.
52119A
18.REMOVE FRONT BUMPER COVER
52618
19.REMOVE FRONT LOWER BUMPER ABSORBER
Remove the 5 bolts.
Detach the 2 claws to remove the front lower bumper absorber.
20.DRAIN ENGINE COOLANT
21.DRAIN ENGINE OIL
22.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID
23.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)
for 4WD/AWD:
Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE OIL>REPLACEMENT
24.DRAIN TRANSFER OIL (for 4WD/AWD)
12601B
25.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Lift the front of the No. 1 engine cover sub-assembly to detach the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to detach the clip and remove the No. 1 engine cover sub-assembly.
Attempting to detach both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
17750A
26.REMOVE INLET AIR CLEANER ASSEMBLY
27.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
89661
28.REMOVE ECM
29.REMOVE BATTERY
74404B
30.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Detach the 2 clamps from the battery clamp sub-assembly.
| *1 | No. 2 Engine Wire |
| *2 | Engine Room Main Wire |
| *3 | Positive (+) Battery Terminal |
Detach the 2 clamps and disconnect the engine room main wire and No. 2 engine wire from the battery clamp sub-assembly.
Remove the nut and disconnect the engine room main wire and No. 2 engine wire from the positive (+) battery terminal.
Detach the 2 claws and disconnect the engine room main wire from the No. 2 engine wire.
Remove the 3 bolts and battery clamp sub-assembly.
33820B
31.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)
| *a | Clip |
| *b | 45° to 60° |
While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
33820B
32.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Remove the 4 clips and disconnect the 2 transmission control cables.
23826
33.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.
44773F
34.DISCONNECT UNION TO CHECK VALVE HOSE
Detach the clamp.
Disconnect the union to check valve hose from the vacuum pump assembly.
87246
35.DISCONNECT OUTLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to detach the lock claws and pull off the outlet heater water hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.
87245
36.DISCONNECT INLET HEATER WATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to detach the lock claws and pull off the inlet heater water hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose connector with plastic bags to prevent damage and contamination.
23901
37.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
16571C
38.DISCONNECT NO. 1 RADIATOR HOSE
Remove the clamp to disconnect the No. 1 radiator hose from the No. 1 radiator bracket.
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
39.DISCONNECT NO. 2 RADIATOR HOSE
Detach the radiator hose clamp from the fan shroud.
Slide the clip and disconnect the No. 2 radiator hose from the water inlet.
88704
40.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
88711
41.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
42.DISCONNECT WIRE HARNESS
After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.
Detach the 3 claws.
Remove the No. 2 relay block cover from the engine room relay block and junction block assembly.
|
Nut |
|
Connector |
Remove the nut from the engine room relay block and junction block assembly.
Disconnect the 5 connectors from the engine room relay block and junction block assembly.
Using a screwdriver, detach the claw and separate the wire harness from the engine room relay block and junction block assembly.
for CVT:
Detach the clamp.
Remove the bolt and disconnect No. 3 engine wire from the CVT transaxle assembly.
for Manual Transaxle:
Detach the clamp.
Remove the bolt and disconnect No. 3 engine from the manual transaxle assembly.
Detach the clamp.
Remove the bolt and disconnect the wire harness from the vehicle body.
16282
43.DISCONNECT NO. 5 WATER BY-PASS HOSE
Slide the 2 clips and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.
45220
44.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
17410
45.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43502H
46.REMOVE FRONT AXLE SHAFT NUT LH
43501H
47.REMOVE FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
48.DISCONNECT FRONT SPEED SENSOR LH
49.DISCONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
48810
50.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
51.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
45470
52.DISCONNECT TIE ROD ASSEMBLY LH
45460
53.DISCONNECT TIE ROD ASSEMBLY RH
Use the same procedure described for the LH side.
48069
54.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48069
55.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
43420
56.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
for 4WD/AWD:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for 4WD/AWD)>REMOVAL
43420G
57.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH
for 4WD/AWD:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for 4WD/AWD)>REMOVAL
43410
58.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH
for 4WD/AWD:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY (for 4WD/AWD)>REMOVAL
31481A
59.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)
Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.
Remove the clip and disconnect the clutch hose.
37117
60.REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD/AWD)
37110
61.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
62.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
|
Attachments | - | - |
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
|
Bolt |
|
Nut |
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
for CVT:
Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.
for Manual Transaxle:
Remove the bolt and nut and separate the engine mounting bracket LH from the transverse engine engine mounting insulator.
| *1 | Front Bumper Extension Sub-assembly LH |
| *2 | Front Bumper Extension Sub-assembly RH |
| *3 | Rear Front Suspension Member Brace LH |
| *4 | Rear Front Suspension Member Brace RH |
|
Bolt |
|
Nut |
Remove the 2 bolts (A), 2 bolts (B), 4 nuts and front bumper extension sub-assembly LH and front bumper extension sub-assembly RH from the front frame assembly and vehicle body.
Remove the 2 bolts (C), 4 bolts (D) and rear front suspension member brace LH and rear front suspension member brace RH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
89481B
63.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ GPF)
25760
64.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ GPF)
25706
65.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ GPF)
17167
66.SEPARATE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17118
67.REMOVE MANIFOLD STAY
17141
68.REMOVE EXHAUST MANIFOLD
23825
69.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
70.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
11361J
71.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the cylinder block sub-assembly.
32101A
72.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)
for 4WD/AWD:
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
73.DISCONNECT VACUUM HOSE (w/ Active Control Engine Mount)
16261G
74.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)
16260
75.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
45319
76.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)
77.DISCONNECT WIRE HARNESS
51100H
78.REMOVE FRONT FRAME ASSEMBLY
for 4WD/AWD:
Click hereSuspension>FRONT SUSPENSION>FRONT SUSPENSION MEMBER (for Gasoline Model)>REMOVAL
12361
79.REMOVE FRONT ENGINE MOUNTING INSULATOR (for CVT)
for 4WD/AWD:
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
12371A
80.REMOVE REAR ENGINE MOUNTING INSULATOR (for CVT)
for 4WD/AWD:
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
12361
81.REMOVE FRONT ENGINE MOUNTING INSULATOR (for Manual Transaxle)
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
for 4WD/AWD:
Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE ASSEMBLY>REMOVAL
12371A
82.REMOVE REAR ENGINE MOUNTING INSULATOR (for Manual Transaxle)
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
for 4WD/AWD:
Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE ASSEMBLY>REMOVAL
12311A
83.REMOVE FRONT ENGINE MOUNTING BRACKET
| *A | for CVT |
| *B | for Manual Transaxle |
Remove the 3 bolts and front engine mounting bracket from the transaxle housing.
11363A
84.REMOVE FLYWHEEL HOUSING SIDE COVER
28100
85.REMOVE STARTER ASSEMBLY
w/ Stop And Start System (for CVT):
w/ Stop And Start System (for Manual Transaxle):
for 1.2 kW Type:
Click hereEngine / Hybrid System>M20A-FKS (STARTING)>STARTER (for 1.2 kW Type)>REMOVAL
30300
86.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
for 4WD/AWD:
Click hereDrivetrain>EG62F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE ASSEMBLY>REMOVAL
30400
87.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)
for 4WD/AWD:
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
88.FIX ENGINE ASSEMBLY
Using wooden blocks or plate lift attachments, set the engine on a flat surface.
Place wooden blocks or plate lift attachments so that the engine is level.
Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.
Perform this step while supporting the engine assembly using a sling device and chain block.
31210
89.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31250
90.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
31400
91.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY (for Manual Transaxle)
Click hereDrivetrain>CLUTCH>CLUTCH UNIT>REMOVAL
13405
92.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
32101
93.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
19315
94.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
82121
95.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
96.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
97.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
12305
98.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Disconnect the No. 6 water by-pass hose.
Detach the clamp.
Detach the clamps and disconnect the suction pipe sub-assembly and air conditioning tube and accessory assembly.
Remove the bolt, nut and the radiator reserve tank assembly.
Remove the bolt and disconnect the No. 2 ground wire from the engine mounting insulator sub-assembly RH.
|
Bolt |
|
Nut |
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.
12341
99.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
12372A
100.REMOVE ENGINE MOUNTING INSULATOR LH (for CVT)
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the 4 bolts and rear engine mounting insulator LH from the vehicle body.
12371A
101.REMOVE ENGINE MOUNTING BRACKET LH (for Manual Transaxle)
Perform this procedure only when replacement of the engine mounting bracket LH is necessary.
Remove the bolt from the flexible hose bracket.
Remove the 4 bolts and engine mounting bracket LH from the vehicle body.