Home › Engine / Hybrid System › A25A-FXS (ENGINE CONTROL) › SFI SYSTEM (w/ Canister Pump Module) › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076383 A25A-FXS ENGINE CONTROL _0372716 SFI SYSTEM(w/ Canister Pump Module) C

A25A-FXS ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P014C00  O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D00  O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P015A00  O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B00  O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P003012.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P003012

HINT:

Although the DTC titles say O2 sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P014C00 O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 The rich to lean response rate deterioration level* value is standard or less (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored SAE Code: P014C
P014D00 O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 The lean to rich response rate deterioration level* value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored SAE Code: P014D
P015A00 O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 The rich to lean delay level* value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored SAE Code: P015A
P015B00 O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 The lean to rich delay level* value is standard or more (2 trip detection logic).
·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 1) heater

·

ECM


Comes on DTC stored SAE Code: P015B

*: Calculated by ECM based on the air fuel ratio sensor (sensor 1) output.

MONITOR DESCRIPTION

After the engine has been warmed up, the ECM carries out air fuel ratio feedback control and maintains the air fuel ratio at the theoretical ratio. In addition, after all the preconditions have been met, active air fuel ratio control is performed for approximately 30 seconds. During active air fuel ratio control, the ECM measures the response of the air fuel ratio sensor (sensor 1) by increasing or decreasing a specific injection quantity based on the theoretical air fuel ratio learned during normal air fuel control. The ECM determines whether there is an air fuel ratio sensor (sensor 1) malfunction at the mid-point of active air fuel ratio control.

If the response of the air fuel ratio sensor (sensor 1) has decreased, DTC P014C00 and P014D00 are output.

If the air fuel ratio sensor (sensor 1) output timing is delayed, DTC P015A00 and P015B00 are output.

A223538E51
4.219,1.74 4.063,1.438 false 5.229,1.99 5.448,1.427 false 4.188,2.99 4.073,2.75 false 4.51,3.042 4.76,2.667 false 0.125,0.104 2.677,0.427 2.552,0.323 10 false Air Fuel Ratio Sensor (Sensor 1) Output: 0.177,1.031 1.448,1.458 1.271,0.427 10 false Active Air Fuel Ratio Control 0.135,2.01 2.135,2.458 2,0.448 10 false Air Fuel Ratio Sensor (Sensor 1) Output (Response Rate) 3.594,1.333 4.094,1.521 0.5,0.188 10 false Normal 5.469,1.354 6.229,1.542 0.76,0.188 10 false Malfunction 4.573,0.5 5.781,0.698 1.208,0.198 10 false 30 seconds 0.198,4.229 1.604,4.417 1.406,0.188 10 false Fuel Injection Volume 2.771,4.042 3.417,4.229 0.646,0.188 10 false Increase 2.771,4.5 3.417,4.688 0.646,0.188 10 false Decrease 1.833,0.844 2.229,0.99 0.396,0.146 10 false On 1.833,1.146 2.208,1.333 0.375,0.188 10 false Off 0.135,3.198 2.125,3.625 1.99,0.427 10 false Air Fuel Ratio Sensor (Sensor 1) Output (Delay Time) 3.583,2.688 4.083,2.875 0.5,0.188 10 false Normal 4.792,2.594 5.552,2.781 0.76,0.188 10 false Malfunction

MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Active air fuel ratio control Performing
Active air fuel ratio control is performed when the following conditions are met -
Auxiliary battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idle Off
Engine speed 1000 rpm or higher, and less than 4000 rpm
Air fuel ratio sensor (sensor 1) status Activated
Fuel-cut Off
Engine load 10% or higher, and less than 70%
Catalyst monitor Not yet
Mass air flow 4.5 gm/sec or higher, and less than 15 gm/sec

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation pattern will activate the air fuel ratio sensor (sensor 1) response monitor.


A201252E93
0.677,0.406 1.719,0.938 1.042,0.531 10 false Vehicle Speed 0.021,0.927 1.646,1.542 1.625,0.615 10 false Between 75 and 100 km/h [Engine running] 1.219,2.323 1.667,2.688 0.448,0.365 10 false Idling 0.5,2.604 1.781,2.99 1.281,0.385 10 false Power Switch off 2.354,2.177 2.552,2.365 0.198,0.188 10 false [A] 3.906,0.792 4.115,0.969 0.208,0.177 10 false [B] 2.073,2.906 3.052,3.188 0.979,0.281 10 false Warming up 3.573,2.938 4.542,3.313 0.969,0.375 10 false 10 minutes 5.708,2.781 6.156,3.115 0.448,0.333 10 false Time 4.656,3.042 4.854,3.229 0.198,0.188 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].

10.

Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P014C00, P014D00, P015A00 or P015B00.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>VEHICLE CONTROL HISTORY



HINT:
·

A low air fuel ratio sensor (sensor 1) current could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor (sensor 1) current could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C00, P014D00, P015A00 OR P015B00)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P014C00, P014D00, P015A00 or P015B00 is output A
DTC P014C00, P014D00, P015A00 or P015B00 and other DTCs are output B


HINT:

If any DTCs other than P014C00, P014D00, P015A00 or P015B00 are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (SENSOR 1) (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (SENSOR 1) (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION


HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)

NG

REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C28-1 (HA1A) - C45-9 (HA1A) Always Below 1 Ω
C28-3 (A1A+) - C45-95 (A1A+) Always Below 1 Ω
C28-4 (A1A-) - C45-94 (A1A-) Always Below 1 Ω
C28-1 (HA1A) or C45-9 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C28-3 (A1A+) or C45-95 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C28-4 (A1A-) or C45-94 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C00, P014D00, P015A00 OR P015B00)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C00, P014D00, P015A00 OR P015B00)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P014C00, P014D00, P015A00 or P015B00 is output B




A

B

6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>A25A-FXS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the power switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C00, P014D00, P015A00 OR P015B00)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C00, P014D00, P015A00 OR P015B00)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P014C00, P014D00, P015A00 or P015B00 is output B




A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO