Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0372747 FRONT CAMERA SYSTEM C

CRUISE CONTROL  FRONT CAMERA SYSTEM  C1AA800  Front Recognition Camera Optical Axis Misalignment Malfunction  


DESCRIPTION

If the forward recognition camera determines that the beam axis of the camera is misaligned, it stores C1AA800.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AA800 Front Recognition Camera Optical Axis Misalignment Malfunction While driving at a vehicle speed of 5 km/h (3 mph) or higher after 3 seconds have elapsed since turning the ignition switch to ON, the axis misalignment of the forward recognition camera is detected
·

Windshield glass

·

Vehicle operating conditions

·

Wheel alignment

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


·

When replacing the windshield glass equipped with the forward recognition camera, be sure to replace it with a genuine windshield glass for the forward recognition camera. A windshield glass other than a genuine windshield glass for the forward recognition camera does not have a camera installation bracket. Therefore, the forward recognition camera cannot be installed. If the forward recognition camera is mounted on a windshield glass that is not a genuine windshield glass for the forward recognition camera, the forward recognition camera may not operate properly because of the transmittance of the windshield glass and the shape of black ceramic parts.

·

The beam axis may become misaligned while driving on circuits or banked roads. If this occurs, driving on normal roads for a while will correct the misalignment.

·

The beam axis may become misaligned while driving overloading or when vehicle toe is displaced. If this occurs, re-adjusting the load or adjusting toe-in will correct the misalignment.



PROCEDURE

1.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
a.

Check the forward recognition camera installation condition.

HINT:

Replace the windshield glass if there is a malfunction in the installation condition of the forward recognition camera.


OK:

The forward recognition camera installation bracket is neither deformed nor misaligned.



Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE CONDITION

NG

11.REPLACE WINDSHIELD GLASS
2.CHECK VEHICLE CONDITION
a.

Check the vehicle operating condition.

HINT:

Confirm that the beam axis of the camera was not misaligned due to overloading, towing, modification, etc.


OK:

Nothing has caused the beam axis of the camera to be misaligned.



Result:
Proceed to
OK
NG



OK

3.CHECK WHEEL ALIGNMENT

NG

9.ADJUST FORWARD RECOGNITION CAMERA
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).


OK:

Front and rear wheels are not misaligned (toe).



Result:
Proceed to
OK
NG



OK

4.ADJUST FORWARD RECOGNITION CAMERA

NG

6.ADJUST WHEEL ALIGNMENT
4.ADJUST FORWARD RECOGNITION CAMERA
a.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

END

6.ADJUST WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).



Result:
Proceed to
NEXT



NEXT

7.ADJUST FORWARD RECOGNITION CAMERA
7.ADJUST FORWARD RECOGNITION CAMERA
a.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

END

9.ADJUST FORWARD RECOGNITION CAMERA
a.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

END

11.REPLACE WINDSHIELD GLASS
a.

Replace the windshield glass.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.ADJUST FORWARD RECOGNITION CAMERA
12.ADJUST FORWARD RECOGNITION CAMERA
a.

Perform forward recognition camera adjustment.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC
13.CLEAR DTC
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 430

Result:
Proceed to
NEXT



NEXT

END