The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield glass removal/installation are shown below.
1. PRECAUTION
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also the dynamic radar cruise control system (for HV Model), dynamic radar cruise control system (for Gasoline Model), front camera system, lane control system, road sign assist system, front radar sensor system, pre-collision system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
85292B
2.REMOVE FRONT WIPER ARM HEAD CAP
3.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
4.REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
53867H
5.REMOVE FRONT FENDER TO COWL SIDE SEAL LH
53866J
6.REMOVE FRONT FENDER TO COWL SIDE SEAL RH
Use the same procedure described for the LH side.
55708
7.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
62312B
8.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
9.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62212
10.REMOVE FRONT PILLAR GARNISH LH
62211
11.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74320
12.REMOVE VISOR ASSEMBLY LH
74310
13.REMOVE VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
74348
14.REMOVE VISOR HOLDER
74610U
15.REMOVE ASSIST GRIP ASSEMBLY
16.REMOVE MAP LIGHT ASSEMBLY
89941
17.REMOVE RAIN SENSOR (w/ Rain Sensor)
88620E
18.REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor)
86466E
19.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466D
20.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
87810
21.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87810
22.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
87810
23.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (for Digital Inner Mirror)
86464A
24.REMOVE FORWARD RECOGNITION LATCH (w/ Pre-collision System)
8646C
25.REMOVE FORWARD RECOGNITION CAMERA (w/ Pre-collision System)
86401
26.REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY (w/ Pre-collision System)
27.REMOVE ROOF HEADLINING ASSEMBLY
Remove a sufficient amount of the front portion of the roof headlining assembly so that windshield glass removal and installation procedures can be performed.
Partially remove the roof headlining.
for Normal Roof:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
for Moon Roof:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
for Panoramic Moon Roof:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
56111
28.REMOVE WINDSHIELD GLASS
The windshield glass may fall while performing this procedure. Therefore, use suction cups to hold the windshield glass from the outside of the vehicle.
| *A | for Type A |
| *B | for Type B |
w/ windshield deicer:
Disconnect the windshield deicer connector and detach the clamp.
w/ Heated Windshield Defroster System:
Disconnect the windshield deicer connector.
| *a | Apply protective tape |
|
Protective Tape |
Apply protective tape on the body surface around the outer edge of the windshield glass to the left, right and top sides.
| *a | Matchmarks |
When reusing the windshield glass:
Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.
Install the suction cups to the windshield glass.
| *1 | Windshield Glass Stopper |
| *a | Piano Wire |
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.
Cut through the adhesive by pulling the piano wire around the glass.
Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.
Using suction cups, detach the 2 windshield glass stoppers and windshield glass retainers and remove the windshield glass.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
56115A
29.REMOVE NO. 1 WINDSHIELD GLASS STOPPER
When reusing the windshield glass:
| *a | Backside |
for 1-piece Type:
Using a gasket scraper, remove the 2 No. 1 window glass stoppers from the windshield glass.
Be careful not to damage the windshield glass.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
|
Remove in this Direction |
for 2-piece Type:
Using a gasket scraper, remove the 2 No. 1 window glass stoppers from the body.
Be careful not to damage the windshield glass.
Be sure to replace the No. 1 windshield glass stopper with a new one.
56116C
30.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
| *a | Backside |
When reusing the windshield glass:
Using a gasket scraper, remove the 2 No. 2 window glass stoppers from the windshield glass.
Be careful not to damage the windshield glass.
Be sure to replace the No. 2 window glass stoppers with a new one.
56153C
31.REMOVE FRONT WINDOW INNER CENTER MOULDING
Perform the following procedure only when replacement of the front window inner center moulding is necessary.
Using a scraper, remove the front window inner center moulding.
Be careful not to damage the windshield glass.
Be sure to replace the front window inner center moulding with a new one.