Home › Drivetrain › EG62F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076271 EG62F MANUAL TRANSMISSION / TRANSAXLE _0372179 MANUAL TRANSAXLE SYSTEM C

EG62F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P080512  Clutch Position Sensor "A"Circuit Short to Battery  P080514  Clutch Position Sensor "A"Circuit Short to Ground or Open  


DESCRIPTION

The clutch pedal stroke sensor assembly is installed to the clutch pedal support sub-assembly. It detects the clutch pedal position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P080512 Clutch Position Sensor "A"Circuit Short to Battery Clutch pedal stroke sensor assembly signal voltage is higher than 4.7 V for 5 seconds or more (1-trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Short to +B in clutch pedal stroke sensor assembly circuit

·

ECM


Does not come on DTC stored SAE Code:
P0808
P080514 Clutch Position Sensor "A"Circuit Short to Ground or Open Clutch pedal stroke sensor assembly signal voltage is below 0.3 V for 5 seconds or more (1-trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Open or short to ground in clutch pedal stroke sensor assembly circuit

·

ECM


Does not come on DTC stored SAE Code:
P0807

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 30 seconds or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait for 5 seconds or more with the ignition switch ON.

7.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

8.

Input the DTC: P080512 or P080514.

9.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C364959E07
0.917,3.49 2.167,3.927 1.25,0.438 10 false Clutch Pedal Stroke Sensor Assembly 0.927,3.313 1.385,3.51 0.458,0.198 10 false A82 5.552,3.948 6.01,4.146 0.458,0.198 10 false A24 5.552,4.125 6.01,4.323 0.458,0.198 10 false ECM 5.177,1.833 5.792,2.031 0.615,0.198 10 false VCCL 5.177,2.292 5.635,2.49 0.458,0.198 10 false CLS 5.177,2.75 5.792,2.948 0.615,0.198 10 false E2CL 5.927,1.667 6.385,1.865 0.458,0.198 10 false 5 V 1.844,1.833 2.302,2.031 0.458,0.198 10 false VDD 1.833,2.292 2.292,2.49 0.458,0.198 10 false OUT 1.833,2.74 2.292,2.938 0.458,0.198 10 false GND 4.844,1.833 5.156,2.031 0.313,0.198 10 false 19 4.844,2.292 5.302,2.49 0.458,0.198 10 false 11 4.844,2.74 5.156,2.938 0.313,0.198 10 false 20 2.271,1.833 2.427,2.031 0.156,0.198 10 false 3 2.271,2.292 2.427,2.49 0.156,0.198 10 false 2 2.26,2.74 2.417,2.938 0.156,0.198 10 false 1

PROCEDURE

1.READ VALUE USING GTS (CLUTCH STROKE SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Clutch Stroke Sensor Voltage.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Clutch Stroke Sensor Voltage Clutch pedal stroke sensor assembly output voltage Min.: 0.000 V
Max.: 4.999 V
·

0.96 to 1.04 V: Clutch pedal fully released

·

Value changes progressively (Only increase): Not depressed → Fully depressed (Clutch pedal should be operated slowly)


-
Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
a.
C364961C03
1.448,0.177 1.865,0.417 0.417,0.24 1.406,1.104 1.083,1.667 true 1.667,1.094 2.167,1.667 true 1.542,0.219 2,0.417 0.458,0.198 10 false A82 0.75,1.604 1.208,1.802 0.458,0.198 10 false GND 2.24,1.625 2.698,1.823 0.458,0.198 10 false VDD 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly)


Disconnect the clutch pedal stroke sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A82-3 (VDD) - A82-1 (GND) Ignition switch ON 4.5 to 5.5 V



d.

Turn the ignition switch off.


e.

Connect the clutch pedal stroke sensor assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-2 (OUT) - A24-11 (CLS) Always Below 1 Ω
A82-2 (OUT) or A24-11 (CLS) - Body ground Always 10 kΩ or higher



d.

Connect the clutch pedal stroke sensor assembly connector.


e.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY
a.

Replace the clutch pedal stroke sensor assembly.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC P080512 or P080514 is output B



A

END

B

6.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-1 (GND) - A24-20 (E2CL) Always Below 1 Ω
A82-3 (VDD) - A24-19 (VCCL) Always Below 1 Ω
A82-1 (GND) or A24-20 (E2CL) - Body ground Always 10 kΩ or higher
A82-3 (VDD) or A24-19 (VCCL) - Body ground Always 10 kΩ or higher



d.

Connect the clutch pedal stroke sensor assembly connector.


e.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR