Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › 2018.10–2019.02
RM3620E _53 Suspension _076636 TIRE / WHEEL _0373033 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Inspect the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure (for Korea):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
225/65R17 102H 230 (2.3, 33) 230 (2.3, 33)


Cold Tire Inflation Pressure (for Middle East, General Export, Russia, South Africa, Europe and Australia):
Tire Size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)

*1: For driving under 210 km/h (130 mph).

*2: For driving under 240 km/h (149 mph).

225/65R17 102H 230 (2.3, 33)*1 230 (2.3, 33)*1
225/60R18 100H 230 (2.3, 33)*1 230 (2.3, 33)*1
235/55R19 101V 230 (2.3, 33)*2 230 (2.3, 33)*2


Cold Tire Inflation Pressure (for Compact Spare Tire):
Tire Size kPa (kgf/cm2, psi)
T165/80D17 104M 420 (4.2, 60)
T165/90D18 107M


i.

Perform initialization. (w/ Tire Pressure Warning System)

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION


ii.

Tire pressure adjustment method when warm (w/ Tire Pressure Warning System):

1.

Turn the ignition switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

6.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

7.

Perform initialization and check that initialization completes.

8.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

9.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

10.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


11.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40


b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)



Hide 2. ROTATE TIRES

a.

Remove the wheel assembly.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL


b.
C241094C01
0.401,2.276 0.578,2.429 0.177,0.153 10 *a 0.401,0.557 0.578,0.71 0.177,0.153 10 *a 1.798,0.158 1.975,0.31 0.177,0.153 10 *b 1.798,1.911 1.975,2.064 0.177,0.153 10 *c
*a Front of the Vehicle
*b Vehicle Wheels and Spare Tire Wheel are Same Type
*c Vehicle Wheels and Spare Tire Wheel are Not Same Type, or There is No Spare Tire


If the spare tire uses a different type of wheel than the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.


c.

Install the wheel assembly.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION


d.

Perform initialization. (w/ Tire Pressure Warning System)

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION


Hide 3.INSPECT AND ADJUST WHEEL BALANCE

a.
C264658N01
2.098,3.633 2.240,3.803 0.142,0.170 10 A

for Aluminum Wheel Type:

Inspect and adjust the off-the-car balance.

Maximum imbalance after adjustment:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the sticking surface of the tape.

·

Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

Width (A):

25 mm (0.984 in.)


·

Push the balance weight firmly to adhere it to the position.

·

Do not reuse the balance weight.

·

Use only TOYOTA genuine stick-on type balance weights or equivalent.



HINT:
·

The inner side balance weights should be installed by clipping them to the rim.

·

If necessary, check and adjust the on-the-car balance.




b.
C144019

for Steel Wheel Type:

Inspect and adjust the off-the-car balance.

Maximum imbalance after adjustment:

8.0 g (0.0176 lb)


HINT:

If necessary, check and adjust the on-the-car balance.



Hide 4.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 6.INSPECT REAR AXLE HUB BEARING LOOSENESS