Home › Engine / Hybrid System › CRUISE CONTROL › FRONT RADAR SENSOR SYSTEM
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0373066 FRONT RADAR SENSOR SYSTEM C

CRUISE CONTROL  FRONT RADAR SENSOR SYSTEM  U010487  Lost Communication with Cruise Control Module Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.

If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U010487 Lost Communication with Cruise Control Module Missing Message
Detection condition:

Ignition switch ON


Malfunction status:

Communication malfunction with the forward recognition camera is detected


Malfunction duration:

10 seconds or more


·

Local bus (Open or short)

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.

Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly
(Front Radar Sensor)
Forward Recognition Camera
(Pre-Collision System)
U010487 U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ ○ Local bus (Open or short)
Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)
Pattern 2 ○ - Millimeter wave radar sensor assembly (Internal malfunction)


WIRING DIAGRAM

E384731E09
0.333,1.74 2.313,1.938 1.979,0.198 10 false Forward Recognition Camera 5.344,1.76 6.781,2.125 1.438,0.365 10 false Millimeter Wave Radar Sensor Assembly 0.333,1.552 0.646,1.75 0.313,0.198 10 false P8 5.333,1.594 5.646,1.792 0.313,0.198 10 false B9 1.177,0.792 1.792,0.99 0.615,0.198 10 false CANH 1.188,1.469 1.802,1.667 0.615,0.198 10 false CANL 5.688,0.771 6.302,0.969 0.615,0.198 10 false CA1P 5.688,1.479 6.302,1.677 0.615,0.198 10 false CA1N 1.656,0.76 1.813,0.958 0.156,0.198 10 false 6 1.646,1.25 1.844,1.448 0.198,0.198 10 false 12 5.469,0.771 5.625,0.969 0.156,0.198 10 false 5 5.469,1.24 5.625,1.438 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the millimeter wave radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, forward recognition camera adjustment must be performed.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)




PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Front Radar Sensor: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>DTC CHECK / CLEAR

Pre-Collision System: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Pattern Display on GTS / Output DTC
Millimeter Wave Radar Sensor Assembly
(Front Radar Sensor)
Forward Recognition Camera
(Pre-Collision System)
Pattern 1 U010487 U023587
Pattern 2 U010487 -

Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

2.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY CAN MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B9 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-5 (CA1P) - B9-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B9-5 (CA1P) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-6 (CA1N) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-5 (CA1P) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B9-6 (CA1N) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

4.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)
3.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Front Radar Sensor > Clear DTCs
50002 429

c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
OK:

DTC U010487 is not output.



Result:
Proceed to
OK
NG



OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FORWARD RECOGNITION CAMERA

4.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA CAN MAIN WIRE)
a.

Reconnect the B9 millimeter wave radar sensor assembly connector.


b.

Disconnect the P8 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-6 (CANH) - P8-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
P8-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-12 (CANL) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-6 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
P8-12 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

5.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Front Radar Sensor > Clear DTCs
50002 429

c.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



d.

Recheck for DTCs and check that no DTCs are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429
OK:

DTC U010487 is not output.



Result:
Proceed to
OK
NG



OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FORWARD RECOGNITION CAMERA