After moving the shift lever to M, it is possible to change the shift range between M1 and M10 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (S Range) | Transmission control switch status | ON or OFF | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Tester Display |
|---|
| Shift SW Status (S Range) |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sport Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" or "+" shift paddle switch operated ·
OFF: Shift lever not held in "+" and "+" shift paddle switch released |
- |
| Sport Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" or "-" shift paddle switch operated ·
OFF: Shift lever not held in "-" and "-" shift paddle switch released |
- |
| Tester Display |
|---|
| Sport Shift Up SW |
| Sport Shift Down SW |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
B
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the G23 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| 3 (SFTU) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| 1 (SFTD) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SFTU) - 2 (E) | Shift lever held in "+" | Below 1 Ω |
| 1 (SFTU) - 2 (E) | Shift lever in M | 10 kΩ or higher |
| 3 (SFTD) - 2 (E) | Shift lever held in "-" | Below 1 Ω |
| 3 (SFTD) - 2 (E) | Shift lever in M | 10 kΩ or higher |
Connect the G23 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G23 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-2 (E) - Body ground | Always | Below 1 Ω |
Connect the G23 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C33 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C33-14 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| C33-14 (SFTU) - Body ground | Shift lever in M | 10 kΩ or higher |
| C33-13 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| C33-13 (SFTD) - Body ground | Shift lever in M | 10 kΩ or higher |
Connect the C33 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch)) |
Disconnect the G23 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in M | 10 kΩ or higher |
Connect the G23 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G23 shift lock control unit assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G23-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| G23-4 (IG) - Body ground | Ignition switch off | Below 1 V |
Connect the G23 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C33 TCM connector.
Disconnect the G23 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G23-5 (S) - C33-30 (S) | Always | Below 1 Ω |
| G23-5 (S) or C33-30 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C33 TCM connector.
Connect the G23 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the TCM.
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION