Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0373331 THEFT DETERRENT SYSTEM D

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  SYSTEM DESCRIPTION  


OUTLINE OF THEFT DETERRENT SYSTEM


·

The theft deterrent system can be set by locking the doors using any of the following operations:

-

Entry lock operation*

-

Wireless lock operation

-

Key linked lock operation

-

By opening and closing the doors

HINT:
for vehicles not displaying the item "Security control with mechanism key" on the GTS for vehicles displaying the item "Security control with mechanism key" on the GTS
Entry lock operation* ○ ○
Wireless lock operation ○ ○
Key linked lock operation ○ -
By opening and closing the doors ○ -

·

○: Available

·

-: Not Available



*: w/ Entry Function



·

In the armed state, the alarm function will be activated if one of the following conditions is met:

-

Any of the doors are unlocked.

-

Any of the doors, the engine hood or the back door is opened.

-

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement inside the cabin.*1

-

The tilt sensor (theft warning ultrasonic and tilt sensor) detects that the vehicle is tilted.*1

-

The glass breakage sensor detects that glass is broken.*2

*1: w/ Intrusion Sensor Cancel Switch

*2: w/ Glass Breakage Sensor



·

In the alarm sounding state, the system blinks the turn signal lights. At the same time, the system sounds the vehicle horns and security horn assembly*1 or theft warning siren assembly*2 to deter break-in and theft as well as to warn people around the vehicle.

*1: w/ Security Horn Assembly

*2: w/o Security Horn Assembly


·

The theft deterrent system can be canceled by unlocking the doors using the following operation:

-

Entry unlock operation*1

-

Wireless unlock operation

-

Key linked unlock operation

HINT:
for vehicles not displaying the item "Security control with mechanism key" on the GTS for vehicles displaying the item "Security control with mechanism key" on the GTS
Entry unlock operation*1 ○ ○
Wireless unlock operation ○ ○
Key linked unlock operation ○ -
(○)*2

·

○: Available

·

-: Not Available



*1: w/ Entry Function

*2: This function is set through the customize function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>CUSTOMIZE PARAMETERS



·

The theft deterrent system has an active arming mode. There are 4 states in this mode: a disarmed state, an arming preparation state, an armed state and an alarm sounding state.


a.

Disarmed state:

·

The alarm function is not operating.

·

The theft deterrent system is not operating.



b.

Arming preparation state:

·

The time until the system goes into the armed state.

·

The theft deterrent system is not operating.



c.

Armed state:

·

The theft deterrent system is operating.



d.

Alarm sounding state:

·

The alarm function is operating.


Alarm time:

Approximately 27.5 seconds


Alarm Methods
Alarm Method Turn Signal Lights Blinking
Vehicle Horns Sounding
(approximately 0.4-seconds cycles)
Security Horn Assembly*1 Sounding
(approximately 0.4-seconds cycles)
Theft Warning Siren Assembly*2 Sounding

*1: w/ Security Horn Assembly

*2: w/o Security Horn Assembly




FUNCTION OF MAIN COMPONENTS


Component Function
Security indicator light Informs driver of theft deterrent system status.
·

Security horn assembly*1

·

Theft warning siren assembly*2


Sounds when attempted break-in or theft is detected.
Turn signal lights Blink when attempted break-in or theft is detected.
Vehicle horns Sound when attempted break-in or theft is detected.
·

Front door courtesy light switch assembly (for LH/RH)

·

Rear door courtesy light switch assembly (for LH/RH)


Detects door status (open or closed).
Door unlock detection switch Detects door status (locked or unlocked).
Hood lock assembly (engine hood courtesy switch) Detects engine hood status (open or closed).
Back door lock assembly with courtesy light switch (back door courtesy light switch) Detects back door status (open or closed).
Intrusion sensor cancel switch*3
·

Sends a signal to the main body ECU (multiplex network body ECU) to cancel the intrusion sensor (theft warning ultrasonic and tilt sensor).

·

Sends a signal to the main body ECU (multiplex network body ECU) to cancel the tilt sensor (theft warning ultrasonic and tilt sensor).


Certification ECU (smart key ECU assembly)*4
·

Receives wireless door lock/unlock signal.

·

Receives entry door lock/unlock signal.


Main body ECU (multiplex network body ECU)*5 Receives wireless door lock/unlock signal.
Intrusion sensor (theft warning ultrasonic and tilt sensor)*3 Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting an intrusion.
Tilt sensor (theft warning ultrasonic and tilt sensor)*3 Sends a signal to the main body ECU (multiplex network body ECU) to sound the alarm when detecting a change in the pitch angle of the vehicle inclination.
Glass breakage sensor*6 Sounds alarm when the quarter window assembly LH/RH or back door glass is broken, or when there is short in the wire harness.

*1: w/ Security Horn Assembly

*2: w/o Security Horn Assembly

*3: w/ Intrusion Sensor Cancel Switch

*4: w/ Entry and Start System

*5: w/o Entry and Start System

*6: w/ Glass Breakage Sensor



ACTIVE ARMING MODE


a.

Active arming mode:

This system operates as described in the diagram below when one of the items for each condition is met.

HINT:

The term "all doors" used in this section refers to the driver door, front passenger door, rear door LH, rear door RH and back door.


B214494E13
1.688,1.521 3.146,1.76 1.458,0.24 10 Disarmed State (1)*1 2.302,3.188 4.021,3.396 1.719,0.208 10 Arming Preparation State 2.729,4.583 3.573,4.729 0.844,0.146 10 Armed State 2.406,5.99 3.99,6.24 1.583,0.25 10 Alarm Sounding State 0.24,6.979 3.438,7.198 3.198,0.219 10 *1: Disarmed state 1 is the normal disarmed state 0.24,7.313 5.792,7.583 5.552,0.271 10 *2: Disarmed state 2 is set from either the disarmed state 1 or arming preparation state 1.052,2.531 1.927,2.781 0.875,0.25 10 Condition [3] 3.771,4 4.719,4.26 0.948,0.26 10 Condition [2] 2.948,2.531 3.906,2.781 0.958,0.25 10 Condition [1] 3.833,5.365 4.823,5.677 0.99,0.313 10 Condition [4] 2.469,5.365 3.375,5.635 0.906,0.271 10 Condition [6] 0.563,4.469 1.448,4.708 0.885,0.24 10 Condition [5] 0.563,5.865 1.469,6.135 0.906,0.271 10 Condition [5] 4.99,1.521 6.438,1.771 1.448,0.25 10 Disarmed State (2)*2 1.083,0.885 2.198,1.146 1.115,0.26 10 Disarmed State 3.573,1.25 4.469,1.479 0.896,0.229 10 Condition [9] 3.573,1.906 4.479,2.135 0.906,0.229 10 Condition [8] 4.51,2.531 5.479,2.802 0.969,0.271 10 Condition [7] 4.958,3.469 5.948,3.74 0.99,0.271 10 Condition [10]

for vehicles not displaying the item "Security control with mechanism key" on the GTS
Condition Item
Condition [1] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood closed, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors locked and the engine hood closed, the state changes from any of the doors being opened to all doors being closed.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation.

·

Any door is unlocked.

·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).


Condition [4] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.

·

The tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of the vehicle inclination.

·

The glass breakage sensor detects that glass is broken.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation, entry operation or key linked power door lock operation.

·

When 5 seconds or more have elapsed after the engine switch is pressed, the engine switch is turned from off to on (IG) without pressing the engine switch.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlock.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.


Condition [5] One of the following conditions is met:
·

The engine switch is turned on (IG) and the engine is running at 550 rpm for 2 seconds or more.

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation.

·

The engine switch is turned on (ACC) or on (IG) within 5 seconds after the engine switch is pushed.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and the system returns to the armed state.


Condition [7] One of the following conditions is met:
·

The engine hood is closed with all the doors closed.

·

The power back door reservation lock is operated with the engine hood and a door other than the back door closed.


Condition [8] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).

·

All doors are unlocked by wireless operation, entry operation or key linked power door lock operation.

·

During a close operation, the power back door reverses operation, stops partway or another door opens.


Condition [9] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the engine hood open, all doors are locked by wireless operation, entry operation or key linked power door lock operation.

·

With all doors locked and engine hood open, the state changes from any of the doors being opened to all doors being closed.

·

During a power back door close operation with all other doors closed, the doors are locked (power back door reservation lock) by wireless operation.


Condition [10]
·

The engine hood is opened.



for vehicles displaying the item "Security control with mechanism key" on the GTS with Entry and Start System for HV Model
Condition Item
Condition [1] In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood closed, all doors are locked by wireless operation or entry operation.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation or entry operation.

·

Any door is unlocked.

·

Any door is opened.

·

The power switch is pushed.

·

The power switch is turned on (ACC) or on (IG).

·

The auxiliary battery is reconnected.*1


Condition [4] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.*2

·

The tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of the vehicle inclination.*2

·

The glass breakage sensor detects that glass is broken.*3

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or entry operation.

·

When 5 seconds or more have elapsed after the power switch is pressed, the power switch is turned from off to on (IG) without pressing the power switch.

·

The auxiliary battery is reconnected when the engine hood is open, any door is open or any door is unlock.

·

The engine hood is open.

·

Any door is open.

·

The power switch is on (IG).


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.*2


Condition [5] One of the following conditions is met:
·

The power switch is turned on (READY).

·

All doors are unlocked by wireless operation or entry operation.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to the armed state.


Condition [7] One of the following conditions is met:
·

The engine hood is closed with all the doors closed.

·

The power back door reservation lock is operated with the engine hood and a door other than the back door closed.*4


Condition [8] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

The power switch is pushed.

·

The power switch is turned on (ACC) or on (IG).

·

The auxiliary battery is reconnected.*1

·

All doors are unlocked by wireless operation or entry operation.

·

During a close operation, the power back door reverses operation, stops partway or another door opens.*4


Condition [9] In disarmed state 1, when the power switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the engine hood open, all doors are locked by wireless operation or entry operation.

·

During a power back door close operation with all other doors closed, the doors are locked (power back door reservation lock) by wireless operation.*4


Condition [10]
·

The engine hood is opened.



*1: w/o Door Control Battery

*2: w/ Intrusion Sensor Cancel Switch

*3: w/ Glass Breakage Sensor

*4: w/ Power Back Door System


for vehicles displaying the item "Security control with mechanism key" on the GTS with Entry and Start System for Gasoline Model
Condition Item
Condition [1] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors and the engine hood closed, all doors are locked by wireless operation or entry operation.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation or entry operation.

·

Any door is unlocked.

·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).

·

The battery is reconnected.*1


Condition [4] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.*2

·

The tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of the vehicle inclination.*2

·

The glass breakage sensor detects that glass is broken.*3

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked not by wireless operation or entry operation.

·

When 5 seconds or more have elapsed after the engine switch is pressed, the engine switch is turned from off to on (IG) without pressing the engine switch.

·

The battery is reconnected when the engine hood is open, any door is open or any door is unlock.

·

The engine hood is open.

·

Any door is open.

·

The engine switch is on (IG).


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.*2


Condition [5] One of the following conditions is met:
·

The engine switch is turned on (IG) and the engine is running at 550 rpm for 2 seconds or more.

·

All doors are unlocked by wireless operation or entry operation.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to the armed state.


Condition [7] One of the following conditions is met:
·

The engine hood is closed with all the doors closed.

·

The power back door reservation lock is operated with the engine hood and a door other than the back door closed.*4


Condition [8] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

The engine switch is pushed.

·

The engine switch is turned on (ACC) or on (IG).

·

The battery is reconnected.*1

·

All doors are unlocked by wireless operation or entry operation.

·

During a close operation, the power back door reverses operation, stops partway or another door opens.*4


Condition [9] In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·

With all doors closed and the engine hood open, all doors are locked by wireless operation or entry operation.

·

During a power back door close operation with all other doors closed, the doors are locked (power back door reservation lock) by wireless operation.*4


Condition [10]
·

The engine hood is opened.



*1: w/o Door Control Battery

*2: w/ Intrusion Sensor Cancel Switch

*3: w/ Glass Breakage Sensor

*4: w/ Power Back Door System


for vehicles displaying the item "Security control with mechanism key" on the GTS without Entry and Start System
Condition Item
Condition [1] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors and the engine hood closed, all doors are locked by wireless operation.


Condition [2]
·

Allow approximately 30 seconds to elapse.


Condition [3] One of the following conditions is met:
·

All doors are unlocked by wireless operation.

·

Any door is unlocked.

·

Any door is opened.

·

Key is in the key cylinder.

·

The ignition switch is turned to ACC or ON.


Condition [4] One of the following conditions is met:
·

The engine hood is opened when the engine hood is closed.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) detects movement within the vehicle.*1

·

The tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of the vehicle inclination.*1

·

The glass breakage sensor detects that glass is broken.*2

·

The battery is reconnected when the engine hood is open, any door is open or any door is unlock.

·

Any door is opened when all doors are closed.

·

Any door is unlocked when all doors are locked.

·

The ignition switch is turned to ON when the key is not in the key cylinder.

·

The engine hood is open.

·

Any door is unlocked.

·

Any door is opened

·

The ignition switch is ON when the key is not in the key cylinder.


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.*1


Condition [5] One of the following conditions is met:
·

The ignition switch is turned to ON and the engine is running at 550 rpm for 2 seconds or more.

·

All doors are unlocked by wireless operation.


Condition [6]
·

After approximately 27.5 seconds, the alarm stops and 5 seconds later the system returns to the armed state.


Condition [7]
·

The engine hood is closed when the engine hood is opened.


Condition [8] One of the following conditions is met:
·

Any door is unlocked when all doors are locked.

·

Any door is opened.

·

Key is in the key cylinder.

·

The ignition switch is turned to ACC or ON.

·

All doors are unlocked by wireless operation.


Condition [9] In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·

With all doors closed and the engine hood opened, all doors are locked by wireless operation.


Condition [10]
·

The engine hood is opened.



*1: w/ Intrusion Sensor Cancel Switch

*2: w/ Glass Breakage Sensor




FORCED DOOR LOCK CONTROL


a.

The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (armed state), all doors are forced to lock by a forced door lock signal.

i.

If the following conditions are met, the forced door lock control is operated.

·

The key is not in the key cylinder.*

·

The theft deterrent system is in the armed state.

·

Any door is unlocked.


*: w/o Entry and Start System





PANIC ALARM CONTROL (w/ Panic Switch)


a.

Panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the panic switch on the electrical key transmitter sub-assembly.

i.

Conditions that cause panic alarm control to set off the panic alarm:

The panic switch on the electrical key transmitter sub-assembly is pressed under the following conditions:

·

The ignition switch is off.

·

The theft deterrent system is not in the alarm sounding state.



ii.

Conditions that cause the panic alarm control to shut off the alarm:

Any of the following conditions is met during panic alarm control operation:

·

The ignition switch is ON.

·

The panic switch is pressed again.

·

Any of the switches on the electrical key transmitter sub-assembly (lock/unlock/back door open*) is pressed.

·

The panic alarm ends (approximately 27.5 seconds have elapsed).

·

The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system controls the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.


*: w/ Power Back Door System





INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR) (w/ Intrusion Sensor Cancel Switch)


NOTICE:

Ultrasonic waves are used to detect intrusion. Ultrasonic waves do not penetrate steel or glass. When any of the door windows is left open, ultrasonic waves may escape. This may result in the detection of people in the surroundings, leaves or insects entering the vehicle, strong wind or other ultrasonic wave sources in the environment when the vehicle is parked with the door windows open. When parking the vehicle with the door windows open for ventilation, turn off the intrusion sensor (theft warning ultrasonic and tilt sensor) using the intrusion sensor cancel switch.


a.

An intrusion sensor (theft warning ultrasonic and tilt sensor) is provided in the map light sub-assembly located in the front of the vehicle interior.


b.

The main body ECU (multiplex network body ECU) activates the intrusion sensor (theft warning ultrasonic and tilt sensor) when the system changes from the disarmed state to the armed preparation state. If an intrusion detection signal is input from the intrusion sensor (theft warning ultrasonic and tilt sensor) during the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to output an alarm.


c.

When the system is in the disarmed state, the function of the intrusion sensor (theft warning ultrasonic and tilt sensor) can be disabled by pressing the intrusion sensor cancel switch.


d.

The intrusion sensor (theft warning ultrasonic and tilt sensor) may erroneously detect intrusion in the following states:

·

Persons or pets are in the vehicle.

·

The vehicle is parked in a place where extreme vibrations or noises occur, such as in a parking garage.

·

Ice or snow is removed from the vehicle, causing the vehicle to receive repeated impacts or vibrations.

·

The wind or something similar causes an externally mounted reflectively coated windshield cover to move.

·

The intrusion sensor (theft warning ultrasonic and tilt sensor) may react to a hanger or other objects hanging in the cabin when they drop or swing.

·

The system changes to the armed state even when any of the windows is open. The intrusion sensor (theft warning ultrasonic and tilt sensor) may react to objects moving outside the vehicle when any of the windows is open.

·

The vehicle is inside an automatic or high-pressure car wash.

·

The vehicle experiences impacts, such as hail, lightning strikes and other kinds of repeated impacts or vibrations.




TILT SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR) (w/ Intrusion Sensor Cancel Switch)


a.

The tilt sensor (theft warning ultrasonic and tilt sensor) detects the pitch angle of vehicle inclination using 2 deceleration sensors. When the tilt sensor (theft warning ultrasonic and tilt sensor) detects a change in the pitch angle of vehicle inclination, such as a thief attempting to tow the vehicle, it transmits the warning signal to the main body ECU (multiplex network body ECU).


b.

The main body ECU (multiplex network body ECU) activates the tilt sensor (theft warning ultrasonic and tilt sensor) when the system changes from the armed preparation state to the armed state. If a warning signal is received from the tilt sensor (theft warning ultrasonic and tilt sensor) when in the armed state, the main body ECU (multiplex network body ECU) changes to the alarm sounding state in order to sound the alarm.


c.

When the system is in the disarmed state, pressing the intrusion sensor cancel switch disables the function of the tilt sensor (theft warning ultrasonic and tilt sensor). If the system changes to the armed state, the tilt sensor (theft warning ultrasonic and tilt sensor) will not activate. This function is canceled each time all doors are unlocked by the wireless operation, entry operation*1 or key linked power door lock operation*2, and is reinstated when the tilt sensor (theft warning ultrasonic and tilt sensor) is on.

*1: w/ Entry and Start System

*2: for vehicles not displaying the item "Security control with mechanism key" on the GTS



d.

Under the following conditions, if the vehicle tilts or acceleration in the vertical or horizontal direction is detected by the tilt sensor (theft warning ultrasonic and tilt sensor), the alarm may activate accidentally. To avoid accidental alarm activation, turn the tilt sensor (theft warning ultrasonic and tilt sensor) off using the intrusion sensor cancel switch.

·

The vehicle is transported by a ferry, trailer or train.

·

The vehicle is parked in a multi-story parking facility.

·

The vehicle is washed by a conveyor type car washing machine.

·

A tire blows out.

·

The vehicle is jacked up for a tire or wheel change.

·

An earthquake occurs or the road subsides.

·

Goods such as skis or snowboards are loaded or unloaded.




THEFT WARNING SIREN ASSEMBLY (w/o Security Horn Assembly)


a.

The theft warning siren assembly has an internal battery. If power to the theft warning siren assembly is interrupted or the communication line is open, the theft warning siren assembly detects it and sounds the alarm using the internal battery.


b.

The theft warning siren assembly has the following alarm controls: normal alarm control and open circuit alarm control. Under normal alarm control, the alarm sounds based on instructions from the main body ECU (multiplex network body ECU) whereas under open circuit alarm control, the theft warning siren assembly judges current security conditions and sounds the alarm by itself.

i.

Normal alarm control

The theft warning siren assembly sounds when the theft deterrent system is in the alarm sounding state and does not sound when the system is not in the alarm sounding state.

HINT:

If communication interruption between the theft warning siren assembly and main body ECU (multiplex network body ECU) continues for 70 seconds or more while the theft deterrent system is in the alarm sounding state, the theft warning siren assembly stops sounding.



ii.
B315877E02
0.083,0.083 2.979,0.458 2.896,0.375 10 false Conditions of theft warning siren assembly 1.292,0.875 2.26,1.125 0.969,0.25 10 false Disarmed State 1.385,2.219 2.323,2.469 0.938,0.25 10 false Armed State 0.958,1.667 1.104,1.813 0.146,0.146 10 false *1 2.448,1.677 2.729,1.854 0.281,0.177 10 false *2 0.458,3.177 2.99,3.531 2.531,0.354 10 false *1: Theft deterrent system changes to the armed state. 0.479,3.938 3.031,4.323 2.552,0.385 10 false *2: Theft deterrent system changes to the disarmed state.

Open circuit alarm control

The theft warning siren assembly changes between the disarmed state and armed state in accordance with the theft deterrent system changes between the disarmed state and armed state. If the power source, ground or communication line is open while the theft warning siren assembly is in the armed state, the theft warning siren assembly sounds.

During the open circuit alarm sounding state, the theft warning siren assembly sounds intermittently for 28 seconds and then stops for 5 seconds. This pattern repeats a maximum of 9 times.

The intermittent sound will stop when either condition is met:
1.

The theft warning siren changes to the disarmed state.

2.

The open circuit is returned to normal.


B267215E15
0.063,0.083 3.781,0.302 3.719,0.219 10 false (a) Intermittent sound pattern repeats a maximum of 9 times 0.229,0.427 2.74,0.635 2.51,0.208 10 false Theft warning siren is in the armed state 1.854,1.25 2.76,1.49 0.906,0.24 10 false Circuit is open 1.729,1.76 2.75,2 1.021,0.24 10 false Circuit is normal 1.031,2.063 3.469,2.302 2.438,0.24 10 false Theft warning siren sounds 0.729,2.573 2.802,2.823 2.073,0.25 10 false Theft warning siren sounds stop 1.854,8.031 2.76,8.271 0.906,0.24 10 false Circuit is open 1.729,8.552 2.75,8.781 1.021,0.229 10 false Circuit is normal 1.031,8.854 3.281,9.083 2.25,0.229 10 false Theft warning siren sounds 0.729,9.365 2.76,9.615 2.031,0.25 10 false Theft warning siren sounds stop 0.063,0.917 2.729,1.146 2.667,0.229 10 false Theft warning siren is in the disarmed state 0.26,7.219 2.75,7.438 2.49,0.219 10 false Theft warning siren is in the armed state 0.063,7.708 2.729,7.938 2.667,0.229 10 false Theft warning siren is in the disarmed state 1.854,4.719 2.76,4.927 0.906,0.208 10 false Circuit is open 1.729,5.229 2.75,5.469 1.021,0.24 10 false Circuit is normal 1.031,5.531 3.375,5.75 2.344,0.219 10 false Theft warning siren sounds 0.729,6.052 2.75,6.302 2.021,0.25 10 false Theft warning siren sounds stop 0.26,3.896 2.76,4.146 2.5,0.25 10 false Theft warning siren is in the armed state 0.063,4.396 2.74,4.604 2.677,0.208 10 false Theft warning siren is in the disarmed state 4.74,0.083 5.833,0.281 1.094,0.198 10 false T1: 28 seconds 3.344,2.417 3.531,2.563 0.188,0.146 10 false T1 3.531,2.885 3.719,3.031 0.188,0.146 10 false T2 3.333,5.885 3.521,6.031 0.188,0.146 10 false T1 3.333,9.188 3.521,9.333 0.188,0.146 10 false T1 3.531,9.656 3.719,9.802 0.188,0.146 10 false T2 6.052,0.083 6.948,0.344 0.896,0.26 10 false T2: 5 seconds 0.063,3.229 2.604,3.458 2.542,0.229 10 false (b) The open circuit is returned to normal 0.219,3.5 4.073,3.729 3.854,0.229 10 false (1) The open circuit is returned to normal within 28 seconds 0.219,6.792 4.948,7.021 4.729,0.229 10 false (2) The open circuit is returned to normal after 28 seconds or more elapsed




SECURITY INDICATOR LIGHT OUTPUT


a.

According to the state of the theft deterrent system, the main body ECU (multiplex network body ECU) outputs a signal to turn the security indicator light on. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the main body ECU (multiplex network body ECU).

Output
State of Theft Deterrent System Security Indicator Light
Output Signal from Main Body ECU (Multiplex Network Body ECU) Actual Lighting Condition
Disarmed state (1), (2) Off
·

Off (Immobiliser function unset)

·

Blinking (Immobiliser function set)


Arming preparation state On On
Armed state Off Blinking
Alarm sounding state On On

Blinking Cycle
Time Security Indicator Light
0.125 seconds On
1.875 seconds Off

HINT:

When the immobiliser function is set, the security indicator light blinks during both the disarmed state and the armed state due to output signals from the immobiliser function.




CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC AND TILT SENSOR) (w/ Intrusion Sensor Cancel Switch)


a.

Check that the engine hood is closed.


b.

Check the intrusion sensor (theft warning ultrasonic and tilt sensor) operation.

*1: w/ Entry Function

*2: w/ Entry and Start System


i.

Turn the ignition switch off.


ii.

Lock all the doors using the wireless operation or entry operation*1 and check that the security indicator light illuminates (armed preparation state) (all windows need to be opened).


iii.

Wait 30 seconds after locking all the doors using the wireless operation or entry operation*1 and check that the security indicator light blinks (armed state). Then, check that the theft deterrent system alarm operates due to movement inside the vehicle.

HINT:

If the electrical key transmitter is within the entry exterior area at this time, the alarm does not operate due to the intrusion sensor.*2



iv.

Perform an unlock operation using the wireless operation or entry operation*1 to stop the alarm.




CHECK INTRUSION SENSOR CANCEL SWITCH (w/ Intrusion Sensor Cancel Switch)


a.

Check that the engine hood is closed.


b.

Check the intrusion sensor cancel switch operation.

*1: w/ Entry Function

*2: w/ Entry and Start System


i.

Turn the ignition switch off.


ii.

Press the intrusion sensor cancel switch and check that "Theft Sensor Turned OFF" is displayed on the combination meter.


iii.

Lock all the doors using the wireless operation or entry operation*1 and check that the security indicator light illuminates (armed preparation state).


iv.

Approximately 30 seconds after locking all the doors via wireless operation or entry operation*1, check that the security indicator light changes to blinking (armed state) and the auto alarm does not operate according to movement in the cabin. At this time, do not bring the electrical key transmitter sub-assembly close to the entry exterior area*2.

HINT:

Even if the intrusion sensor (theft warning ultrasonic and tilt sensor) is off, the theft deterrent system is in the armed state. Therefore, if any of the doors is manually unlocked, the alarm operates.