Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3620E _55 Steering _076851 POWER ASSIST SYSTEMS _0374399 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage  


DESCRIPTION

When a problem occurs in the power source circuit, the fail-safe function works to stop the power assist.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1551 IG Power Supply Voltage When the PIG power supply voltage is normal, the IG power supply voltage is 18.5 V or higher
·

Harness or connector

·

Rack and pinion power steering gear assembly

·

Stop and start system (w/ Stop and Start System)


EPS warning light: Comes on The ECU judges the system has returned to normal -

WIRING DIAGRAM

C409579E02
3.667,1.042 4.469,1.25 0.802,0.208 10 false EPS-IG1 3.802,0.5 4.365,0.708 0.563,0.208 10 false EPS 5.073,0.802 5.354,1.063 0.281,0.26 10 false 4 5.083,0.25 5.323,0.438 0.24,0.188 10 false 8 5.094,1.646 5.458,1.885 0.365,0.24 10 false 7 5.677,0.906 6.063,1.177 0.385,0.271 10 false IG 5.656,0.354 6.021,0.604 0.365,0.25 10 false PIG 5.667,1.771 6.271,2.104 0.604,0.333 10 false PGND 5.25,2.052 6.583,2.479 1.333,0.427 10 false Power Steering ECU 5.167,2.75 6.667,3.583 1.5,0.833 10 false Rack and Pinion Power Steering Gear Assembly 5.167,2.583 5.521,2.771 0.354,0.188 10 false C54 3.396,1.51 3.698,1.688 0.302,0.177 10 false A32 3.688,1.51 4.063,1.667 0.375,0.156 10 false G62 2.417,1.906 3.479,2.292 1.063,0.385 10 false Engine Stop and Start ECU *2 3.396,1.344 3.688,1.552 0.292,0.208 10 false 6*3 3.729,1.333 4.073,1.51 0.344,0.177 10 false 6*4 0.292,2.802 2.219,3.01 1.927,0.208 10 false *1: w/o Stop and Start System 0.302,3.156 2.198,3.385 1.896,0.229 10 false *2: w/ Stop and Start System 2.365,2.802 3.281,3 0.917,0.198 10 false *3: for LHD 2.365,3.156 3.073,3.365 0.708,0.208 10 false *4: for RHD 4.385,0.813 4.698,1.01 0.313,0.198 10 false *1 4.396,1.427 4.708,1.625 0.313,0.198 10 false *2 2.99,1.51 3.604,1.708 0.615,0.198 10 false IG11

CAUTION / NOTICE / HINT

NOTICE:
·

If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - RACK AND PINION POWER STEERING GEAR ASSEMBLY)
a.

Disconnect the C54 rack and pinion power steering gear assembly connector.

C374510C47
1.958,0.271 2.375,0.521 0.417,0.25 3.49,1.167 4.625,0.719 false 2.031,0.313 2.5,0.573 0.469,0.26 10 false C54 4.677,0.604 5.146,0.865 0.469,0.26 10 false IG 0.125,0.094 0.594,0.354 0.469,0.26 10 false *a
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C54-4 (IG) - Body ground Ignition switch ON Below 18.5 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

2.CHECK FOR DTC

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

2.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > EMPS > Clear DTCs
50002 142

b.

Check for DTCs.

Chassis > EMPS > Trouble Codes
50001 142

Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

REPLACE RACK AND PINION POWER STEERING GEAR ASSEMBLY

B