Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E402626E04
1.229,0.469 3.521,0.667 2.292,0.198 10 false from TAIL Relay 3.885,0.667 4.656,0.865 0.771,0.198 10 false PANEL 5.979,1.74 6.438,1.938 0.458,0.198 10 false ILL+ 3.26,2.198 3.719,2.396 0.458,0.198 10 false IL-2 3.26,1.635 3.719,1.833 0.458,0.198 10 false IL+2 0.49,3.573 4.771,3.771 4.281,0.198 10 false Steering Pad Switch Assembly 2.771,1.729 3.083,1.927 0.313,0.198 10 false z6 2.76,2.292 3.073,2.49 0.313,0.198 10 false z6 3.802,1.729 4.115,1.927 0.313,0.198 10 false G20 3.813,2.302 4.125,2.5 0.313,0.198 10 false G20 3.833,1.542 4.146,1.74 0.313,0.198 10 false 14 3.875,2.115 4.188,2.313 0.313,0.198 10 false 9 2.792,1.542 3.104,1.74 0.313,0.198 10 false 1 2.792,2.104 3.104,2.302 0.313,0.198 10 false 6 2.615,2.75 4.563,3.021 1.948,0.271 10 false Spiral Cable Sub-assembly 5.781,3.708 7,4.115 1.219,0.406 10 false Radio and Display Receiver Assembly 5.625,1.75 6.844,2.156 1.219,0.406 10 false G2 5.969,3.031 6.458,3.292 0.49,0.26 10 false GND1 5.646,1.552 5.958,1.75 0.313,0.198 10 false 15 5.677,2.833 5.99,3.031 0.313,0.198 10 false 1 5.635,3.031 6.854,3.438 1.219,0.406 10 false G3 0.021,0.042 3.281,0.323 3.26,0.281 12 false w/o Rheostat Control Switch:

E408073E01
0.115,0.104 3.094,0.396 2.979,0.292 12 false w/ Rheostat Control Switch: 0.344,4.625 2.385,4.875 2.042,0.25 10 false Steering Pad Switch Assembly 2.531,4.875 4.552,5.344 2.021,0.469 10 false Spiral Cable Sub-assembly 5.229,6.208 7.083,6.5 1.854,0.292 10 false Combination Meter Assembly 5.24,6.021 5.854,6.219 0.615,0.198 10 false G18 5.615,2.083 6.229,2.281 0.615,0.198 10 false 15 5.865,5.708 6.479,5.906 0.615,0.198 10 false ILL- 5.896,3.927 6.51,4.125 0.615,0.198 10 false ILL- 5.583,5.594 5.781,5.823 0.198,0.229 10 false 35 5.344,4.802 7.063,5.313 1.719,0.51 10 false Radio and Display Receiver Assembly 5.625,3.813 6.24,4.01 0.615,0.198 10 false 16 2.604,2.302 2.917,2.5 0.313,0.198 10 false z6 2.594,4.042 2.906,4.24 0.313,0.198 10 false z6 5.365,4.594 5.823,4.792 0.458,0.198 10 false G2 3.885,2.292 4.198,2.49 0.313,0.198 10 false G20 3.885,4.052 4.198,4.25 0.313,0.198 10 false G20 2.625,2.073 3.24,2.271 0.615,0.198 10 false 1 2.646,3.823 3.26,4.021 0.615,0.198 10 false 6 3.958,3.833 4.573,4.031 0.615,0.198 10 false 9 3.917,2.073 4.531,2.271 0.615,0.198 10 false 14 3.208,2.167 3.823,2.365 0.615,0.198 10 false IL+2 3.25,3.948 3.865,4.146 0.615,0.198 10 false IL-2 5.875,2.198 6.49,2.396 0.615,0.198 10 false ILL+ 5.646,1.24 6.823,1.5 1.177,0.26 10 false to Other Systems 2.656,5.688 3.833,5.948 1.177,0.26 10 false to Other Systems 3.51,0.948 4.688,1.208 1.177,0.26 10 false PANEL 1.646,0.781 2.823,1.042 1.177,0.26 10 false from TAIL Relay

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for HV Model with Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION

for Gasoline Model with Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION

w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ Rheostat Control Switch: A
w/o Rheostat Control Switch: B



A

2.CHECK ILLUMINATION

B

8.CHECK ILLUMINATION
2.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

3.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

3.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E270420C45
1.5,0.25 1.875,0.479 0.375,0.229 2.24,1.5 2.313,1.917 2.313,1.917 2.479,1.917 true 0.969,1.927 1.146,1.927 1.146,1.927 1.313,1.5 true 2.531,1.833 2.917,2.021 0.385,0.188 10 false IL+2 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.552,0.281 1.865,0.479 0.313,0.198 10 false G20 0.688,1.844 1.073,2.031 0.385,0.188 10 false IL-2
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-9 (IL-2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G20-14 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E364302C27
1.583,0.302 2,0.594 0.417,0.292 2.385,0.615 2.229,0.615 2.229,0.615 2.135,1.375 true 2.802,2.021 2.646,2.021 2.646,2.021 2.438,1.438 true 1.708,0.375 2.167,0.573 0.458,0.198 10 false G2 2.438,0.552 2.792,0.74 0.354,0.188 10 false ILL+ 0.219,0.125 0.667,0.333 0.448,0.208 10 false *a 2.865,1.948 3.219,2.135 0.354,0.188 10 false ILL-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-15 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the G18 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-16 (ILL-) - G18-35 (ILL-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

9.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

10.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

9.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E270420C46
1.5,0.25 1.875,0.479 0.375,0.229 2.24,1.5 2.313,1.917 2.313,1.917 2.479,1.917 true 2.531,1.833 2.917,2.021 0.385,0.188 10 false IL+2 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.563,0.281 1.875,0.479 0.313,0.198 10 false G20
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G20-14 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E364302C27
1.583,0.302 2,0.594 0.417,0.292 2.385,0.615 2.229,0.615 2.229,0.615 2.135,1.375 true 2.802,2.021 2.646,2.021 2.646,2.021 2.438,1.438 true 1.708,0.375 2.167,0.573 0.458,0.198 10 false G2 2.438,0.552 2.792,0.74 0.354,0.188 10 false ILL+ 0.219,0.125 0.667,0.333 0.448,0.208 10 false *a 2.865,1.948 3.219,2.135 0.354,0.188 10 false ILL-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-15 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR