Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2018.10–2020.08
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The DCM (telematics transceiver) sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the DCM (telematics transceiver).

WIRING DIAGRAM

E380010E19
1,1.531 1.458,1.729 0.458,0.198 10 false M3 1,1.729 2.74,2.094 1.74,0.365 10 false Stereo Component Amplifier Assembly 4.969,0.781 5.208,0.99 0.24,0.208 10 false 17 2.052,0.771 2.281,0.958 0.229,0.188 10 false 24 1.521,0.927 1.979,1.125 0.458,0.198 10 false TMUT 5.292,0.896 5.781,1.094 0.49,0.198 10 false MUTE 4.99,1.531 5.448,1.729 0.458,0.198 10 false H6 5,1.719 6.938,1.958 1.938,0.24 10 false DCM (Telematics Transceiver)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK DCM (TELEMATICS TRANSCEIVER)
a.
E283621C17
1.458,0.208 1.948,0.469 0.49,0.26 1.042,0.365 1.292,0.365 1.292,0.365 1.458,1.198 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.625,0.25 2.021,0.448 0.396,0.198 10 false H6 0.615,0.271 1.177,0.469 0.563,0.198 10 false MUTE
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H6-17 (MUTE) - Body ground Ignition switch ACC, audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM [TELEMATICS TRANSCEIVER])
a.

Disconnect the M3 stereo component amplifier assembly connector.


b.

Disconnect the H6 DCM (telematics transceiver) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-24 (TMUT) - H6-17 (MUTE) Always Below 1 Ω
M3-24 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the DCM (telematics transceiver) connector.


b.
E176650C93
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.646,0.781 1.99,0.979 0.344,0.198 10 false H6
*a Front view of wire harness connector
(to DCM [Telematics Transceiver])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-17 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE DCM (TELEMATICS TRANSCEIVER)

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY