Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0374524 ROAD SIGN ASSIST SYSTEM Y

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the road sign assist system, make sure that the pre-collision system and lane control system are not malfunctioning.

Pre-collision system: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Lane control system: Click hereEngine / Hybrid System>CRUISE CONTROL>LANE CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Perform the following procedure to troubleshoot the road sign assist system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
2.CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
a.

Interview the customer and confirm the problem.


Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check in CAN Communication System.

for HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

for Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC*

NG

5.CHECK FOR DTC*
a.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 431

b.

Make a note of the output DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK FOR VEHICLE CONTROL HISTORY*

B

7.RECONFIRM DTC OUTPUT*
6.CHECK FOR VEHICLE CONTROL HISTORY*
a.

Check for vehicle control history and note any codes that are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55

b.

Record the vehicle control history.


Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

B

8.RECONFIRM VEHICLE CONTROL HISTORY*
7.RECONFIRM DTC OUTPUT*
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 431

b.

Reproduce the detection conditions of the recorded DTC.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Recheck for DTCs.

i.

Attempt to duplicate the malfunction and check if the DTCs are output again.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 431


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.CHECK FOR VEHICLE CONTROL HISTORY*

B

8.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Clear the vehicle control history.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55

b.

Recheck for vehicle control history.

i.

Check if the following vehicle control history is output.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Road Sign Assist > Utility
Tester Display
Vehicle Control History (RoB)
50005 431 55


Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

B