Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM
RM3620E _58 Vehicle Interior _076039 PRE-COLLISION _0369995 PRE-COLLISION SYSTEM Y

PRE-COLLISION  PRE-COLLISION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the pre-collision system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT AUXILIARY BATTERY VOLTAGE
2.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK MULTI-INFORMATION DISPLAY
3.CHECK MULTI-INFORMATION DISPLAY
a.

Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.

HINT:

If more than one warning message is displayed, check in the order of A, B, C and D.



Result:
Result Proceed to
"VSC Turned Off Pre-Collision Brake System Unavailable" is displayed A
"Pre-Collision System Malfunction Visit Your Dealer" is displayed B
Any of the following messages is displayed:
·

"Pre-Collision System Unavailable"

·

"Pre-Collision System Unavailable Clean Sensor"

·

"Front Camera Unavailable"

·

"Front Camera Vision Blocked Clean and Demist Windshield"


C
Pre-collision system warning message is not displayed D



A

B

4.CHECK CAN COMMUNICATION SYSTEM*

C

6.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)

D

9.PROBLEM SYMPTOMS TABLE
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check if the CAN communication system is functioning normally.

for HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC* (PRE-COLLISION SYSTEM)

NG

5.CHECK FOR DTC* (PRE-COLLISION SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTC C142571 is output B
A DTC other than C142571 is output C



A

6.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)

B

C

8.CHECK FOR DTC* (PRE-COLLISION SYSTEM)
6.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
a.

Check for vehicle control history and note any codes that are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55
i.

Record the vehicle control history.



Result:
Result Proceed to
Vehicle control history is not output A
X2013, X2015, X2022, X2024, X2025, X2026 or X2028 is output B
Vehicle control history other than X2013, X2015, X2022, X2024, X2025, X2026 and X2028 is output C



A

B

C

7.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
7.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
a.

Clear the vehicle control history.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

b.

Recheck for vehicle control history.

i.

Check if the following vehicle control history is output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55


Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

B

8.CHECK FOR DTC* (PRE-COLLISION SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

b.

Reproduce the detection conditions of the recorded DTC.

HINT:

Refer to the flowchart for the detection conditions for each of the DTCs.



c.

Recheck for DTCs.

i.

Attempt to duplicate the malfunction and check if the DTCs are output again.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432


Result:
Result Proceed to
DTCs are not output A
DTC is output B



A

B

9.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B



A

10.CHECK PCS WARNING LIGHT

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

10.CHECK PCS WARNING LIGHT
a.

Check the condition of the PCS warning light.


Result:
Result Proceed to
Only the PCS warning light is illuminated. A
The PCS warning light is not illuminated. B



A

11.CHECK FOR VEHICLE CONTROL HISTORY* (X2015)

B

12.CHECK FOR DTC* (PRE-COLLISION SYSTEM)
11.CHECK FOR VEHICLE CONTROL HISTORY* (X2015)
a.

Check for vehicle control history and note any codes that are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55

Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC* (PRE-COLLISION SYSTEM)
a.

Check for DTCs.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
DTCs are not output A
DTC is output B



A

13.CHECK CONFIRMED DTC DETECTION CONDITION*

B

14.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
13.CHECK CONFIRMED DTC DETECTION CONDITION*
a.

Check detection condition for the confirmed pre-collision system DTC.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>FAIL-SAFE CHART


Result:
Proceed to
NEXT



NEXT

END
a.

Explain to the customer the cause of the previously stored DTC and that the output reason has been cleared.



14.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
a.

Check for vehicle control history and note any codes that are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Pre-Collision System > Utility
Tester Display
Vehicle Control History (RoB)
50005 432 55
i.

Record the vehicle control history.



Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

15.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE

B

16.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
15.CONDITIONS WHEN PRE-COLLISION SYSTEM OPERATE OR NOT OPERATE
a.

Check the conditions when pre-collision system operates or does not operate.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>PRECAUTION


Result:
Result Proceed to
Any condition is met. A
No condition is met. B



A

END (OPERATION/NO OPERATION CONDITIONS OF PRE-COLLISION SYSTEM IS MET)

B

17.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)
16.CHECK FOR VEHICLE CONTROL HISTORY* (PRE-COLLISION SYSTEM)
a.

Check for vehicle control history and note any codes that are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY

HINT:

Based on the customer's inquiry, check the corresponding factors in the vehicle control history, such as the detection time and date, trip information and elapsed time.



Result:
Proceed to
NEXT



NEXT

END
a.

Explain to the customer the cause of the previously stored vehicle control history and that the output reason has been cleared.



17.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY* (FRONT BEAM AXIS MISALIGNMENT READING)
NOTICE:

Before performing beam axis adjustment, check the fitting of the front bumper cover and radiator grille assembly and confirm that there is no warping or deformation.




c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Turn the cruise control main switch on.


g.

Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.

Body Electrical > Front Radar Sensor > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 429 4405

h.

Check the amount of misalignment and make a note.

Standard (before performing adjustment):
Front beam axis misalignment value:
Vertical -5.0 to 5.0 deg.
Horizontal -0.5 to 0.5 deg.



Result:
Result Proceed to
Front beam axis misalignment value is within the specified range. A
Front beam axis misalignment value is not within the specified range. B



A

B