Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B242E  Open in IG Circuit  


DESCRIPTION

The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.

The IG terminal power source voltage is supplied by turning the IG1 NO. 1 relay to ON.

The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IG terminal and monitors the result.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B242E Open in IG Circuit
Detection condition:

The ignition switch is ON


Malfunction status:

When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received


Malfunction duration:

10 seconds or more


·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH

·

Harness or connector


·

Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly RH


-

WIRING DIAGRAM

E370857E09
0.292,0.708 2.281,0.906 1.99,0.198 10 false from IG1 NO. 1 Relay 2.458,0.875 3.521,1.156 1.063,0.281 10 false ECU-IG1 NO. 3 4.708,1.885 5.146,2.125 0.438,0.24 10 false A11 4.719,4.115 5.125,4.354 0.406,0.24 10 false A12 4.708,2.031 7.021,2.313 2.313,0.281 10 false Headlight ECU Sub-assembly LH 4.708,4.25 7.125,4.5 2.417,0.25 10 false Headlight ECU Sub-assembly RH 5.021,0.625 5.229,0.875 0.208,0.25 10 false 4 5.01,2.844 5.219,3.094 0.208,0.25 10 false 4 5.188,0.729 5.427,0.948 0.24,0.219 10 false IG 5.188,2.948 5.427,3.167 0.24,0.219 10 false IG 4.948,1.25 5.156,1.5 0.208,0.25 10 false 12 4.938,3.469 5.146,3.719 0.208,0.25 10 false 12 5.177,1.354 5.552,1.615 0.375,0.26 10 false GND 5.177,3.563 5.552,3.823 0.375,0.26 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION



PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361
Body Electrical > HL AutoLeveling (Sub) > Clear DTCs
50002 414

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
Body Electrical > HL AutoLeveling (Sub) > Trouble Codes
50001 414
OK:

DTC B242E is not output.



Result:
Result Proceed to
OK A
NG (DTC output from headlight ECU sub-assembly LH) B
NG (DTC output from headlight ECU sub-assembly RH) C



A

B

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)

C

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - BODY GROUND)
E411296C01
1.5,0.531 1.896,0.833 0.396,0.302 1.688,2.5 1.823,1.865 false 0.625,2.521 0.76,1.885 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A11 1.604,2.531 1.917,2.729 0.313,0.198 10 false IG 0.563,2.563 0.875,2.76 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


a.

Disconnect the headlight ECU sub-assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A11-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A11-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY RH - BODY GROUND)
E355660C99
1.5,0.531 1.896,0.833 0.396,0.302 1.688,2.5 1.823,1.865 false 0.604,2.51 0.781,1.906 false 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a 1.573,0.604 1.885,0.802 0.313,0.198 10 false A12 1.604,2.531 1.917,2.729 0.313,0.198 10 false IG 0.469,2.531 0.781,2.729 0.313,0.198 10 false GND
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


a.

Disconnect the headlight ECU sub-assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A12-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A12-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR