Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Triple Beam Headlight)
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375585 HEADLIGHT ASSEMBLY(for Triple Beam Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Triple Beam Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are installed, removed or replaced during the headlight ECU sub-assembly LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Headlight ECU sub-assembly LH
·

Vehicle information registration for the headlight ECU sub-assembly LH

·

Initialization of the headlight ECU sub-assembly LH


Automatic headlight beam level control system (Click here)

NOTICE:

Even if the headlight ECU sub-assembly RH is replaced with a new one, vehicle information registration and initialization are not necessary.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



Hide 81156A 2.REMOVE HEADLIGHT BRACKET LH

NOTICE:

If the headlight bracket LH has been removed, replace the No. 2 headlight gasket with a new one.


a.
B552299C01
0,0 0,0 false
V100135

Connector
V100136

"TORX" Screw


Disconnect the connector.


b.

Using a T20H "TORX" driver, remove the "TORX" screw.


c.
B552300C02
2.167,1.646 1.813,1.813 true 2.833,4.01 2.688,3.75 true 1.583,1.729 1.813,1.917 0.229,0.188 10 true *a 2.813,4.031 3.021,4.219 0.208,0.188 10 true *b
*a Matchmark
*b Unlock Position Mark
V113147

Turn in this Direction


Turn the headlight bracket LH counterclockwise until the matchmark is aligned with the unlock position mark and remove it.


Hide 81134D 3.REMOVE NO. 2 HEADLIGHT GASKET

a.
B552302

Remove the No. 2 headlight gasket.

NOTICE:

Do not reuse the No. 2 headlight gasket.



Hide 81510C 4.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E407142

Disconnect the connector.


b.
E409869C01
2.375,0.271 1.729,0.406 true 1.26,2.969 0.76,2.563 true 2.427,0.167 2.656,0.354 0.229,0.188 10 true *a 0.542,2.427 0.75,2.615 0.208,0.188 10 true *b
*a Matchmark
*b Unlock Position Mark
V113147

Turn in this Direction


Turn the bulb socket counterclockwise until the matchmark is aligned with the unlock position mark and remove it.


c.
E403986C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front turn signal light bulb from the bulb socket.


Hide 81194A 5.REMOVE HEADLIGHT PROTECTOR LH

a.
E403988

Remove the headlight protector LH.

NOTICE:

Do not reuse the headlight protector LH.



Hide 81056A 6.REMOVE HEADLIGHT ECU SUB-ASSEMBLY LH

Hide 81134 7.REMOVE HEADLIGHT GASKET

Hide 8110B 8.REMOVE HEADLIGHT LENS SUB-ASSEMBLY LH

NOTICE:
·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E404005C01
1.594,0.583 2.385,0.323 true 1.052,3.469 0.656,3.365 true 2.417,0.229 2.646,0.417 0.229,0.188 10 true *a 0.458,3.26 0.667,3.448 0.208,0.188 10 true *b
*a Matchmark
*b Unlock Position Mark
V113147

Turn in this Direction


Turn the headlight back cover counterclockwise until the matchmark is aligned with the unlock position mark and remove it.


b.
E404007

Disconnect the connector.


c.
E404008C01
3.031,2.229 3.25,2.417 0.219,0.188 10 false *a
*a "TORX" Screw


Remove the 7 screws.


d.

Using a T20H "TORX" driver, remove the "TORX" screw.


e.

Detach the claw.

E404009


f.
B524515C01
1.906,1.104 2.219,1.26 0.313,0.156 10 false *a
*a 7.6 mm (0.299 in.)


Prepare a cable tie with a width of 7.6 mm (0.299 in.).

HINT:

Cable ties with a narrow width (2.5 mm (0.098 in.) etc.) are difficult to pull out through the headlight lens gasket.



g.
E453999

Using a dryer, warm the area around the cable tie insertion area on the headlight lens gasket at the rear of the headlight housing.

NOTICE:

To prevent the headlight housing from deformation or damage, do not heat one part intensively and do not heat with a temperature of 120°C or higher.


HINT:

The headlight lens gasket becomes soft and easy to pull through when warmed.



h.

Insert a cable tie between the headlight lens sub-assembly LH and headlight housing and pull out the headlight lens gasket as shown in the illustration.

E454000C01
4.177,0.677 3.667,0.781 true 6.365,1.125 5.969,1.104 true 3.094,1.156 3.01,0.719 true 2.781,1.604 3.063,1.365 true 5.125,1.583 5.406,1.344 true 5.417,1.135 5.333,0.698 true 5.698,0.406 6.104,0.656 true 4.24,0.573 4.552,0.729 0.313,0.156 10 false *1 6.385,1.031 6.698,1.188 0.313,0.156 10 false *2 2.906,0.51 3.219,0.667 0.313,0.156 10 false *3 2.667,1.646 2.865,1.813 0.198,0.167 10 true *4 5.479,0.281 5.792,0.438 0.313,0.156 10 false *1 5.052,1.604 5.25,1.771 0.198,0.167 10 true *4 5.219,0.51 5.531,0.667 0.313,0.156 10 false *3
*1 Cable Tie *2 Headlight Lens Gasket
*3 Headlight Lens Sub-assembly LH *4 Headlight Housing


NOTICE:

Do not damage the groove in the headlight housing or the surface of the headlight lens sub-assembly LH.



i.

Pull out the headlight lens gasket until there is no contact between the headlight lens sub-assembly LH and the headlight housing.

HINT:

If the headlight lens gasket is disconnected while being pulled out, insert a cable tie between the headlight lens sub-assembly LH and headlight housing and pull out the headlight lens gasket again.



j.

Lift up the headlight lens sub-assembly LH directly upwards to remove it.

E404018C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 81132B 9.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wipe with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.

Remove the remaining headlight lens gasket from the headlight lens and headlight housing.

E404015C01
0.167,0.188 0.583,0.521 0.417,0.333 12 false *A 3.458,0.177 3.875,0.51 0.417,0.333 12 false *B
*A Headlight Lens Side *B Headlight Housing Side
V100144

Headlight Lens Gasket - -



Hide 81160A 10.REMOVE HEADLIGHT LED UNIT ASSEMBLY LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop antistatic mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the headlight LED unit assembly LH with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wipe with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04020, 09891-04010, 09891-04030, 09891-04040)

a.
E404030

Remove the 3 screws.


b.

Detach the guide to remove the turn signal reflector with inner lens.


c.
E404031

Disconnect the connector.


d.
E404032C01
2.813,2.719 3.021,2.917 0.208,0.198 10 true *a 1.177,3.021 1.385,3.219 0.208,0.198 10 true *a
*a Protrusion Amount Measurement Area
V100155

Protective Tape


Apply protective tape as shown in the illustration.


e.

Using a vernier caliper, measure and record the dimensions of the protrusion of the aiming screws for beam axis vertical and horizontal adjustments.


f.
E404033C01
0,0 0,0 false
V113147

Loosen in this Direction


Loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise until there is flush with the aiming screw holder.


g.

Insert the screwdriver headlight LED unit assembly LH from the back side until the pivot as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



h.

Hold the headlight LED unit assembly LH with one hand and twist the screwdriver to detach it from the pivot.

NOTICE:

Do not touch the metallic surface to the headlight housing.


E404035C01
4.083,2.625 4.281,2.823 0.198,0.198 10 true *a 3.135,3.115 3.333,3.313 0.198,0.198 10 true *a
*a Make the aiming screws for beam axis vertical and horizontal adjustments flush with the aiming screw holder. - -
V113147

Twist in this Direction
V100155

Protective Tape



i.
E404033C01
0,0 0,0 false
V113147

Loosen in this Direction


Hold the headlight LED unit assembly LH with one hand to prevent it from tipping over and loosen the aiming screws for beam axis vertical and horizontal adjustments counterclockwise until the headlight LED unit assembly LH is removed.

NOTICE:

Do not touch the metallic surface to the headlight housing.