Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2650 Slide Sensor Malfunction Slide motor position sensor signal not received when power seat moved forward or backward.
·

Position control ECU assembly (driver seat)

·

Slide motor (front seat adjuster assembly [driver seat])

·

Harness or connector



WIRING DIAGRAM

B510519E10
0.469,3.083 6.885,3.281 6.417,0.198 10 false Front Seat Adjuster Assembly (Driver Seat) 1.406,2.469 2.406,2.708 1,0.24 10 false T1*1, S1*2 1.417,2.615 3.104,2.813 1.688,0.198 10 false Slide Motor 2.198,0.438 2.354,0.635 0.156,0.198 10 false 4 2.198,0.948 2.354,1.146 0.156,0.198 10 false 1 2.198,1.469 2.354,1.667 0.156,0.198 10 false 2 2.198,1.979 2.354,2.177 0.156,0.198 10 false 3 5.219,0.531 5.833,0.729 0.615,0.198 10 false SLD+ 5.219,1.042 5.833,1.24 0.615,0.198 10 false SLD- 5.219,1.563 5.833,1.76 0.615,0.198 10 false SSRS 5.219,2.073 5.833,2.271 0.615,0.198 10 false SGND 4.844,1.073 5.302,1.271 0.458,0.198 10 false S7 4.844,0.552 5.302,0.75 0.458,0.198 10 false S7 4.854,2.104 5.313,2.302 0.458,0.198 10 false S8 4.844,1.594 5.302,1.792 0.458,0.198 10 false S8 4.823,0.292 5.219,0.49 0.396,0.198 10 false 1*2 4.823,0.823 5.281,1.021 0.458,0.198 10 false 5*2 4.792,1.333 5.406,1.531 0.615,0.198 10 false 26*2 4.792,1.854 5.406,2.052 0.615,0.198 10 false 12*2 4.354,1.073 4.813,1.271 0.458,0.198 10 false T7 4.354,0.563 4.813,0.76 0.458,0.198 10 false T7 4.365,2.094 4.823,2.292 0.458,0.198 10 false T8 4.375,1.583 4.833,1.781 0.458,0.198 10 false T8 4.323,0.302 4.781,0.5 0.458,0.198 10 false 1*1 4.333,0.823 4.792,1.021 0.458,0.198 10 false 5*1 4.302,1.333 4.917,1.531 0.615,0.198 10 false 26*1 4.302,1.833 4.917,2.031 0.615,0.198 10 false 12*1 4.802,2.594 6.771,3.167 1.969,0.573 10 false Position Control ECU Assembly (Driver Seat) 3.958,3.375 5.646,3.573 1.688,0.198 10 false *1: for LHD 5.167,3.375 6.854,3.573 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2650 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT SLIDE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
OK:

Slide motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)

NG

6.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)
a.
E407950C07
1.063,0.167 1.479,0.417 0.417,0.25 1.75,0.167 2.167,0.417 0.417,0.25 0.156,0.083 0.396,0.333 0.24,0.25 10 false *a 1.875,0.219 2.25,0.49 0.375,0.271 10 false S1 1.188,0.219 1.646,0.417 0.458,0.198 10 false T1 1.51,0.177 1.708,0.365 0.198,0.188 10 false *A 2.198,0.188 2.448,0.365 0.25,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Slide Motor [Front Seat Adjuster Assembly (Driver Seat)])


Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T1-2 - T1-3 Slide switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S1-2 - S1-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])

NG

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-26 (SSRS) - T1-2 Always Below 1 Ω
T8-26 (SSRS) or T1-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T1-3 Always Below 1 Ω
T8-12 (SGND) or T1-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-26 (SSRS) - S1-2 Always Below 1 Ω
S8-26 (SSRS) or S1-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S1-3 Always Below 1 Ω
S8-12 (SGND) or S1-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])
a.

Remove the slide motor (front seat adjuster assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the slide motor (front seat adjuster assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T7*1 or S7*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-1 (SLD+) - T1-4 Always Below 1 Ω
T7-1 (SLD+) or T1-4 - Other terminals and body ground Always 10 kΩ or higher
T7-5 (SLD-) - T1-1 Always Below 1 Ω
T7-5 (SLD-) or T1-1 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-1 (SLD+) - S1-4 Always Below 1 Ω
S7-1 (SLD+) or S1-4 - Other terminals and body ground Always 10 kΩ or higher
S7-5 (SLD-) - S1-1 Always Below 1 Ω
S7-5 (SLD-) or S1-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR