Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2651 Reclining Sensor Malfunction Reclining motor position sensor signal not received when power seat moved forward or rearward.
·

Position control ECU assembly (driver seat)

·

Reclining motor (front seatback frame sub-assembly [driver seat])

·

Harness or connector



WIRING DIAGRAM

B510519E11
0.333,3.083 6.75,3.281 6.417,0.198 10 false Front Seatback Frame Sub-assembly (Driver Seat) 1.323,2.469 2.229,2.75 0.906,0.281 10 false T23*1, S23*2 1.323,2.615 3.01,2.813 1.688,0.198 10 false Reclining Motor 2.198,0.438 2.354,0.635 0.156,0.198 10 false 1 2.198,0.948 2.354,1.146 0.156,0.198 10 false 4 2.198,1.469 2.354,1.667 0.156,0.198 10 false 2 2.198,1.979 2.354,2.177 0.156,0.198 10 false 3 5.219,0.531 5.833,0.729 0.615,0.198 10 false RCL+ 5.219,1.042 5.833,1.24 0.615,0.198 10 false RCL- 5.219,1.563 5.833,1.76 0.615,0.198 10 false SSRR 5.219,2.073 5.833,2.271 0.615,0.198 10 false SGND 4.844,1.073 5.302,1.271 0.458,0.198 10 false S6 4.844,0.563 5.302,0.76 0.458,0.198 10 false S7 4.854,2.104 5.313,2.302 0.458,0.198 10 false S8 4.844,1.583 5.302,1.781 0.458,0.198 10 false S8 4.781,0.292 5.177,0.49 0.396,0.198 10 false 10*2 4.823,0.823 5.281,1.021 0.458,0.198 10 false 6*2 4.792,1.333 5.406,1.531 0.615,0.198 10 false 11*2 4.792,1.854 5.406,2.052 0.615,0.198 10 false 12*2 4.365,1.073 4.823,1.271 0.458,0.198 10 false T6 4.365,0.563 4.823,0.76 0.458,0.198 10 false T7 4.365,2.104 4.823,2.302 0.458,0.198 10 false T8 4.375,1.583 4.833,1.781 0.458,0.198 10 false T8 4.281,0.302 4.74,0.5 0.458,0.198 10 false 10*1 4.333,0.823 4.792,1.021 0.458,0.198 10 false 6*1 4.302,1.333 4.917,1.531 0.615,0.198 10 false 11*1 4.302,1.833 4.917,2.031 0.615,0.198 10 false 12*1 4.802,2.594 6.771,3.167 1.969,0.573 10 false Position Control ECU Assembly (Driver Seat) 3.958,3.375 5.646,3.573 1.688,0.198 10 false *1: for LHD 5.167,3.375 6.854,3.573 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>DTC CHECK / CLEAR

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2651 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
3.PERFORM ACTIVE TEST USING GTS (SEAT RECLINING)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
OK:

Reclining motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

6.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.
E407950C08
1.781,0.167 2.198,0.417 0.417,0.25 1.104,0.167 1.521,0.417 0.417,0.25 0.156,0.115 0.396,0.365 0.24,0.25 10 false *a 1.875,0.208 2.25,0.479 0.375,0.271 10 false S23 1.198,0.208 1.51,0.406 0.313,0.198 10 false T23 1.552,0.188 1.75,0.365 0.198,0.177 10 false *A 2.25,0.188 2.51,0.365 0.26,0.177 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to Reclining Motor [Front Seatback Frame Sub-assembly (Driver Seat)])


Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
T23-2 - T23-3 Reclining switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
S23-2 - S23-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])

NG

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])
5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T8-11 (SSRR) - T23-2 Always Below 1 Ω
T8-11 (SSRR) or T23-2 - Other terminals and body ground Always 10 kΩ or higher
T8-12 (SGND) - T23-3 Always Below 1 Ω
T8-12 (SGND) or T23-3 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S8-11 (SSRR) - S23-2 Always Below 1 Ω
S8-11 (SSRR) or S23-2 - Other terminals and body ground Always 10 kΩ or higher
S8-12 (SGND) - S23-3 Always Below 1 Ω
S8-12 (SGND) or S23-3 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])
a.

Remove the reclining motor (front seatback frame sub-assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the reclining motor (front seatback frame sub-assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-10 (RCL+) - T23-1 Always Below 1 Ω
T7-10 (RCL+) or T23-1 - Other terminals and body ground Always 10 kΩ or higher
T6-6 (RCL-) - T23-4 Always Below 1 Ω
T6-6 (RCL-) or T23-4 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-10 (RCL+) - S23-1 Always Below 1 Ω
S7-10 (RCL+) or S23-1 - Other terminals and body ground Always 10 kΩ or higher
S6-6 (RCL-) - S23-4 Always Below 1 Ω
S6-6 (RCL-) or S23-4 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR