When the position control ECU assembly (driver seat) does not receive a front vertical motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2652 | Front Vertical Sensor Malfunction | Front vertical motor position sensor signal not received when power seat moved upward or downward. | ·
Position control ECU assembly (driver seat) ·
Power seat tilt motor assembly (driver seat) ·
Harness or connector |
Initializing the position control ECU assembly (driver seat) will clear the seat position memory.
Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2652 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Tester Display |
|---|
| Front Vertical Operation |
Front vertical motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Rear view of wire harness connector
(to Power Seat Tilt Motor Assembly [Driver Seat]) |
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T9-2 - T9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S9-2 - S9-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T8-10 (SSFV) - T9-2 | Always | Below 1 Ω |
| T8-10 (SSFV) or T9-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| T8-12 (SGND) - T9-3 | Always | Below 1 Ω |
| T8-12 (SGND) or T9-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-10 (SSFV) - S9-2 | Always | Below 1 Ω |
| S8-10 (SSFV) or S9-2 - Other terminals and body ground | Always | 10 kΩ or higher |
| S8-12 (SGND) - S9-3 | Always | Below 1 Ω |
| S8-12 (SGND) or S9-3 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power seat tilt motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL
Inspect the power seat tilt motor assembly (driver seat).
Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.
Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T7-7 (FRV+) - T9-1 | Always | Below 1 Ω |
| T7-7 (FRV+) or T9-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| T6-4 (FRV-) - T9-4 | Always | Below 1 Ω |
| T6-4 (FRV-) or T9-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-7 (FRV+) - S9-1 | Always | Below 1 Ω |
| S7-7 (FRV+) or S9-1 - Other terminals and body ground | Always | 10 kΩ or higher |
| S6-4 (FRV-) - S9-4 | Always | Below 1 Ω |
| S6-4 (FRV-) or S9-4 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG