Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B2275  STSW Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2275 STSW Monitor Malfunction Certification ECU (smart key ECU assembly) internal hybrid activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*)
·

Certification ECU (smart key ECU assembly)

·

Hybrid vehicle control ECU assembly

·

Harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG) and wait 10 seconds or more, then start the hybrid control system 3 times.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

The power source mode changes to on (READY) even though the hybrid control system is not started.

·

The power source mode does not change to on (READY) even though the hybrid control system is started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2275
Power Source Control
·

Starter Request Signal



WIRING DIAGRAM

C375424E10
5.729,0.698 6.104,0.927 0.375,0.229 10 false +B 6.208,1.323 6.583,1.552 0.375,0.229 10 false IC 5.271,1.083 5.646,1.313 0.375,0.229 10 false ST2 5.042,1.073 5.417,1.302 0.375,0.229 10 false 27 1.281,1.094 1.656,1.323 0.375,0.229 10 false ST2 1.615,1.083 1.99,1.313 0.375,0.229 10 false 4 0.375,2.677 0.75,2.906 0.375,0.229 10 false A30 0.375,2.844 3.271,3.26 2.896,0.417 10 false Hybrid Vehicle Control ECU Assembly 4.969,2.698 5.344,2.927 0.375,0.229 10 false G54 4.969,2.865 7.073,3.479 2.104,0.615 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly or certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and wait 25 seconds.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.


e.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

DTC B2285 is not output simultaneously.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the G54 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A30 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specification Condition
G54-27 (ST2) - A30-4 (ST2) Always Below 1 Ω
G54-27 (ST2) or A30-4 (ST2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B498244C46
1.604,0.115 1.969,0.354 0.365,0.24 1.021,1.979 1.219,1.979 1.219,1.979 1.219,1.083 true 1.667,0.167 2.01,0.365 0.344,0.198 10 false G54 0.719,1.885 1.313,2.083 0.594,0.198 10 false ST2 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the certification ECU (smart key ECU assembly) connector.


b.

Reconnect the A30 hybrid vehicle control ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specification Condition
G54-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approximately 3 seconds has elapsed, the power switch is released 8.5 V or higher → 1 V or less



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)