Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the hybrid vehicle control ECU assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*):
·

A malfunction is detected in the communication or communication lines between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU).

·

The communication ID codes of the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) do not match.


·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU assembly

·

Harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the hybrid control system and wait for 10 seconds. If there is a malfunction, the hybrid control system will stop (communication begins within 3 seconds of the hybrid control system start, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) auxiliary battery terminal, start the hybrid control system and wait for 10 seconds (communication begins within 3 seconds of the power switch being turned on (IG), and DTCs are stored after 6 seconds).



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B279986 -

WIRING DIAGRAM

B537420E03
5.302,2.865 7.042,3.229 1.74,0.365 10 false Hybrid Vehicle Control ECU Assembly 6.667,1.604 7.125,1.802 0.458,0.198 10 false 12 V 5.417,0.615 5.875,0.813 0.458,0.198 10 false IMO 5.438,1.771 5.896,1.969 0.458,0.198 10 false IMI 4.719,0.51 5.177,0.708 0.458,0.198 10 false 23 4.708,1.688 5.167,1.885 0.458,0.198 10 false 10 1.698,0.594 2.156,0.792 0.458,0.198 10 false EFII 1.635,1.771 2.094,1.969 0.458,0.198 10 false EFIO 2.052,0.604 2.51,0.802 0.458,0.198 10 false 3 2.052,1.771 2.51,1.969 0.458,0.198 10 false 4 0.677,0.125 1.135,0.323 0.458,0.198 10 false 12 V 0.323,2.833 0.781,3.031 0.458,0.198 10 false G57 0.333,3.021 2.625,3.427 2.292,0.406 10 false ID Code Box (Immobiliser Code ECU) 5.104,0.5 5.563,0.698 0.458,0.198 10 false 23 5.094,1.688 5.552,1.885 0.458,0.198 10 false 10 4.667,0.708 5.125,0.906 0.458,0.198 10 false G63 4.656,1.875 5.115,2.073 0.458,0.198 10 false G63 5.063,0.698 5.521,0.896 0.458,0.198 10 false A30 5.063,1.865 5.521,2.063 0.458,0.198 10 false A30 5.094,2.125 5.406,2.323 0.313,0.198 10 false *1 5.125,0.938 5.438,1.135 0.313,0.198 10 false *1 4.698,0.938 5.01,1.135 0.313,0.198 10 false *2 4.719,2.115 5.031,2.313 0.313,0.198 10 false *2 2.948,3.052 4.635,3.25 1.688,0.198 10 false *1: for LHD 2.917,3.396 4.604,3.594 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly or ID code box (immobiliser code ECU), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Register the communication ID codes.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

C408267C03
4.865,0.073 5.25,0.25 0.385,0.177 4.865,0.323 5.25,0.5 0.385,0.177 5.552,2 5.385,2 5.385,2 4.917,1.104 true 2.75,4.427 2.917,4.427 2.917,4.427 2.917,3.938 false 3.271,4.427 3.104,4.427 3.104,4.427 3.104,3.938 false 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.927,2.958 3.24,3.115 0.313,0.156 10 false *b 2.563,4.313 2.875,4.469 0.313,0.156 10 false *c 3.302,4.323 3.615,4.479 0.313,0.156 10 false *d 0.938,3.896 1.406,4.167 0.469,0.271 10 false GND 5.615,1.927 6.073,2.125 0.458,0.198 10 false IMO 4.927,0.083 5.365,0.323 0.438,0.24 10 false A30 4.938,0.333 5.375,0.573 0.438,0.24 10 false G63 5.344,0.083 5.656,0.281 0.313,0.198 10 false *A 5.344,0.333 5.656,0.531 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
for LHD:
Tester Connection Condition Tool Setting Specified Condition
A30-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

for RHD:
Tester Connection Condition Tool Setting Specified Condition
G63-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform length or shape is abnormal, or IMO terminal stuck at Hi (12 V) C



A

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

B

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)

C

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

C408268C04
4.875,0.083 5.25,0.25 0.375,0.167 4.875,0.313 5.25,0.479 0.375,0.167 4.729,1.01 4.333,1.948 4.333,1.948 4.094,1.948 true 3.052,4.594 3.219,4.594 3.219,4.594 3.219,4.073 false 3.552,4.583 3.385,4.583 3.385,4.583 3.385,4.073 false 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 3.229,3.031 3.542,3.188 0.313,0.156 10 false *b 2.885,4.479 3.198,4.635 0.313,0.156 10 false *c 3.896,1.865 4.188,2.104 0.292,0.24 10 false IMI 4.948,0.094 5.271,0.333 0.323,0.24 10 false A30 3.573,4.49 3.865,4.729 0.292,0.24 10 false *d 0.875,4.031 1.292,4.24 0.417,0.208 10 false GND 4.927,0.323 5.25,0.563 0.323,0.24 10 false G63 5.354,0.094 5.667,0.292 0.313,0.198 10 false *A 5.354,0.323 5.667,0.521 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
for LHD:
Tester Connection Condition Tool Setting Specified Condition
A30-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

for RHD:
Tester Connection Condition Tool Setting Specified Condition
G63-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

4.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Register the ECU communication ID codes.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.


Result:
Result Proceed to
Hybrid control system was started A
Hybrid control system was not started B



A

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

6.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMO)
a.
B532408C02
1.469,0.073 1.833,0.25 0.365,0.177 1.469,0.323 1.833,0.5 0.365,0.177 2.719,0.365 2.531,0.365 2.531,0.365 2.177,1.354 true 1.542,0.083 2,0.281 0.458,0.198 10 false A30 0.177,0.167 0.635,0.365 0.458,0.198 10 false *a 2.781,0.281 3.24,0.479 0.458,0.198 10 false IMO 1.542,0.333 2,0.531 0.458,0.198 10 false G63 1.917,0.094 2.229,0.292 0.313,0.198 10 false *A 1.927,0.333 2.24,0.531 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


Disconnect the hybrid vehicle control ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Switch Condition Specified Condition
A30-23 (IMO) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V)

for RHD:
Tester Connection Switch Condition Specified Condition
G63-23 (IMO) - Body ground Power switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V)



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) B



A

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the G57 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G57-3 (EFII) - A30-23 (IMO) Always Below 1 Ω
G57-3 (EFII) or A30-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher
G57-4 (EFIO) - A30-10 (IMI) Always Below 1 Ω
G57-4 (EFIO) or A30-10 (IMI) - Other terminals and body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G57-3 (EFII) - G63-23 (IMO) Always Below 1 Ω
G57-3 (EFII) or G63-23 (IMO) - Other terminals and body ground Always 10 kΩ or higher
G57-4 (EFIO) - G63-10 (IMI) Always Below 1 Ω
G57-4 (EFIO) or G63-10 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR