Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model)
RM3620E _58 Vehicle Interior _076037 THEFT DETERRENT / KEYLESS ENTRY _0376193 ENTRY AND START SYSTEM(for Start Function, HV Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) is stuck high, the hybrid vehicle control ECU assembly will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery The communication line (IMI - EFIO) between the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).
·

Harness or connector

·

ID code box (immobiliser code ECU)

·

Hybrid vehicle control ECU assembly


DTC output confirmation operation:

Turn the power switch on (IG) and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid control system cannot be started Hybrid control system cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -

WIRING DIAGRAM

B537421E03
0.479,1.885 3.115,2.25 2.635,0.365 10 false ID Code Box (Immobiliser Code ECU) 0.49,1.729 0.958,1.969 0.469,0.24 10 false G57 1.781,0.729 2.25,0.969 0.469,0.24 10 false EFIO 2.177,0.729 2.646,0.969 0.469,0.24 10 false 4 5.01,1.771 6.729,2.135 1.719,0.365 10 false Hybrid Vehicle Control ECU Assembly 5.125,0.719 5.594,0.958 0.469,0.24 10 false IMI 4.406,0.635 4.875,0.875 0.469,0.24 10 false 10 6.354,0.385 6.823,0.625 0.469,0.24 10 false 12 V 4.771,0.833 5.229,1.031 0.458,0.198 10 false A30 4.375,0.833 4.833,1.031 0.458,0.198 10 false G63 4.802,0.625 5.271,0.865 0.469,0.24 10 false 10 4.833,1.073 5.146,1.271 0.313,0.198 10 false *1 4.438,1.073 4.75,1.271 0.313,0.198 10 false *2 3.115,1.979 4.802,2.177 1.688,0.198 10 false *1: for LHD 3.115,2.313 4.802,2.51 1.688,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the hybrid vehicle control ECU assembly or ID code box (immobiliser code ECU), refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279A12 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK CONNECTION OF CONNECTOR
a.

Turn the power switch off.


b.

Check that the connectors are properly connected to the hybrid vehicle control ECU assembly and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Result:
Result Proceed to
The connectors are properly connected A
The connectors are not properly connected B



A

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)

B

CONNECT CONNECTORS PROPERLY

2.CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

C408268C05
4.875,0.083 5.25,0.25 0.375,0.167 4.875,0.333 5.25,0.5 0.375,0.167 4.729,1.01 4.333,1.948 4.333,1.948 4.094,1.948 true 3.052,4.594 3.219,4.594 3.219,4.594 3.219,4.073 false 3.552,4.583 3.385,4.583 3.385,4.583 3.385,4.073 false 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 3.229,3.031 3.542,3.188 0.313,0.156 10 false *b 2.885,4.479 3.198,4.635 0.313,0.156 10 false *c 3.896,1.865 4.188,2.104 0.292,0.24 10 false IMI 4.948,0.094 5.271,0.333 0.323,0.24 10 false A30 3.573,4.49 3.865,4.729 0.292,0.24 10 false *d 0.875,4.031 1.292,4.24 0.417,0.208 10 false GND 4.948,0.344 5.271,0.583 0.323,0.24 10 false G63 5.354,0.094 5.667,0.292 0.313,0.198 10 false *A 5.354,0.333 5.667,0.531 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Component with harness connected
(Hybrid Vehicle Control ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
for LHD:
Tester Connection Condition Tool Setting Specified Condition
A30-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

for RHD:
Tester Connection Condition Tool Setting Specified Condition
G63-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal waveform



A

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

for LHD:

Disconnect the A30 hybrid vehicle control ECU assembly connector.


b.

for RHD:

Disconnect the G63 hybrid vehicle control ECU assembly connector.


c.

Disconnect the G57 ID code box (immobiliser code ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G57-4 (EFIO) - A30-10 (IMI) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
G57-4 (EFIO) - G63-10 (IMI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR