77606
1.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Attach the 4 clips and install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly.
77651A
2.INSTALL NO. 1 FUEL TANK CUSHION
Install 2 new No. 1 fuel tank cushions to the fuel tank assembly.
77026B
3.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Attach the clamp and install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.
77209C
4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Attach the clamp and install the fuel tank main tube sub-assembly to the fuel tank assembly.
77754B
5.INSTALL CHARCOAL CANISTER OUTLET HOSE
Install the charcoal canister outlet hose to the fuel tank assembly.
77100
6.INSTALL FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Set the fuel tank assembly on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Using the engine lifter, slowly raise the fuel tank assembly, and temporarily install the fuel tank assembly and 2 fuel tank band sub-assemblies with the 2 bolts in the order shown in the illustration.
Be careful not to drop the fuel tank assembly.
When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
Using SST, tighten the 4 bolts in the order shown in the illustration.
45 N*m (459 kgf*cm, 33 ft.*lbf)
| *a | LH Side |
| *b | RH Side |
| *c | Torque Wrench Fulcrum Length |
Using SST, install the rear side of the fuel tank band.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 24.5 N*m (250 kgf*cm, 18 ft.*lbf)
77754B
7.CONNECT CHARCOAL CANISTER OUTLET HOSE
Connect the charcoal canister outlet hose to the fuel tank filler pipe assembly.
8.CONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY
Connect the fuel tank filler pipe sub-assembly to the fuel tank filler pipe assembly.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
9.CONNECT FUEL TANK BREATHER TUBE
Connect the fuel tank breather tube to the fuel tank filler pipe assembly.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
77209C
10.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Connect the fuel tank main tube sub-assembly to the fuel tube.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
w/o Cover:
Install the fuel tube protector to the fuel tank main tube sub-assembly.
77026B
11.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel evaporation tube sub-assembly to the charcoal canister assembly, and slide the clamp to secure the tube.
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
77606
12.INSTALL NO. 1 FUEL TANK PROTECTOR
Install the No. 1 fuel tank protector to the fuel tank band with the 2 nuts.
58398F
13.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)
Install the No. 1 floor under cover to the body and tighten the nut.
Attach the 3 clips and install the 2 bolts.
58165C
14.INSTALL FRONT FLOOR COVER RH (w/ Cover)
Install the front floor cover RH to the body and tighten the 3 nuts.
Attach the 2 clips and install the 2 bolts and 4 screws.
58399D
15.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)
Install the No. 2 floor under cover to the body and tighten the 4 nuts.
Attach the 3 clips and install the 2 bolts.
58166A
16.INSTALL FRONT FLOOR COVER LH (w/ Cover)
Install the front floor cover LH to the body and tighten the 3 nuts.
Attach the 3 clips and install the 2 bolts and 5 screws.
51420
17.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
51441
18.INSTALL NO. 1 ENGINE UNDER COVER
53895B
19.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH
53896B
20.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH
37110
21.INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD/AWD)
17408
22.INSTALL TAIL EXHAUST PIPE ASSEMBLY
23.ADD FUEL
77020A
24.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
77010
25.INSTALL FUEL TANK VENT TUBE ASSEMBLY
26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION