Home › Vehicle Interior › HEATING / AIR CONDITIONING › REFRIGERANT LINE(for Gasoline Model)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374854 REFRIGERANT LINE(for Gasoline Model) A

HEATING / AIR CONDITIONING  REFRIGERANT LINE(for Gasoline Model)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 88718L 2.REMOVE PIPING CLAMP (for Suction Hose Sub-assembly Side)

a.

w/o Sub-cool Accelerator:

i.

Press the suction hose sub-assembly to the suction pipe sub-assembly, and then release the piping clamp lock.

NOTICE:

Do not apply excessive force to the suction hose sub-assembly and suction pipe sub-assembly.


E409495C01
4.354,3.594 4.354,3.26 true 5.938,3.656 5.938,3.323 true 4.656,3.594 4.656,3.26 true 4.271,3.583 4.583,3.781 0.313,0.198 10 false *1 5.854,3.646 6.167,3.844 0.313,0.198 10 false *2 4.583,3.594 4.896,3.792 0.313,0.198 10 false *3 0.302,0.552 0.677,0.792 0.375,0.24 12 false *A 0.302,3.604 0.677,3.844 0.375,0.24 12 false *B 3.51,2.604 3.823,2.802 0.313,0.198 10 false *a
*A for A25A-FTS *B for M20A-FTS
*1 Suction Hose Sub-assembly *2 Suction Pipe Sub-assembly
*3 Piping Clamp - -
*a Press In - -



ii.

While releasing the piping clamp lock, use pliers or another tool to pinch near the rear end of the piping clamp, and then disconnect the suction hose sub-assembly as you buckle it.

NOTICE:
·

If any foreign matter is attached to the connecting parts, brush it off or use compressed air to remove it before disconnecting the parts.

·

Make sure that fragments of the piping clamp do not enter the piping.

·

When the piping clamp is buckled, cracks form. Therefore, make sure to replace it with a new one.

·

Remove any foreign matter from the connecting parts of the suction hose sub-assembly and suction pipe sub-assembly.



E409500C01
4.323,4.052 4.323,3.719 true 5.583,4.208 5.583,3.875 true 4.635,4.052 4.635,3.719 true 0.292,0.458 0.667,0.698 0.375,0.24 12 false *A 0.292,3.479 0.667,3.719 0.375,0.24 12 false *B 4.24,4.052 4.583,4.271 0.344,0.219 10 false *1 5.5,4.208 5.844,4.427 0.344,0.219 10 false *2 4.552,4.052 4.896,4.271 0.344,0.219 10 false *3 4.823,4.198 5.167,4.417 0.344,0.219 10 false *a 4.823,2.146 5.167,2.365 0.344,0.219 10 false *a 3.698,3.083 4.042,3.302 0.344,0.219 10 false *b
*A for A25A-FTS *B for M20A-FTS
*1 Suction Hose Sub-assembly *2 Suction Pipe Sub-assembly
*3 Piping Clamp - -
*a Buckle *b Pull Out




b.

w/ Sub-cool Accelerator:

i.

Press the suction hose sub-assembly to the No. 2 air conditioning tube and accessory assembly, and then release the piping clamp lock.

NOTICE:

Do not apply excessive force to the suction hose sub-assembly and No. 2 air conditioning tube and accessory assembly.


E409499C01
4.344,3.594 4.344,3.26 true 5.906,3.656 5.906,3.323 true 4.635,3.604 4.635,3.271 true 0.292,0.552 0.667,0.792 0.375,0.24 12 false *A 0.292,3.583 0.667,3.823 0.375,0.24 12 false *B 5.823,3.656 6.135,3.854 0.313,0.198 10 false *2 4.552,3.604 4.865,3.802 0.313,0.198 10 false *3 4.26,3.594 4.573,3.792 0.313,0.198 10 false *1 3.479,2.635 3.792,2.833 0.313,0.198 10 false *a
*A for A25A-FTS *B for M20A-FTS
*1 Suction Hose Sub-assembly *2 No. 2 Air Conditioning Tube and Accessory Assembly
*3 Piping Clamp - -
*a Press In - -



ii.

While releasing the piping clamp lock, use pliers or another tool to pinch near the rear end of the piping clamp, and then disconnect the suction hose sub-assembly as you buckle it.

NOTICE:
·

If any foreign matter is attached to the connecting parts, brush it off or use compressed air to remove it before disconnecting the parts.

·

Make sure that fragments of the piping clamp do not enter the piping.

·

When the piping clamp is buckled, cracks form. Therefore, make sure to replace it with a new one.

·

Remove any foreign matter from the connecting parts of the suction hose sub-assembly and No. 2 air conditioning tube and accessory assembly.



E409501C01
4.354,4.052 4.354,3.719 true 5.542,4.208 5.542,3.875 true 4.615,4.063 4.615,3.729 true 0.271,0.365 0.646,0.604 0.375,0.24 12 false *A 0.271,3.604 0.646,3.844 0.375,0.24 12 false *B 4.271,4.063 4.646,4.302 0.375,0.24 10 false *1 5.458,4.208 5.833,4.448 0.375,0.24 10 false *2 4.531,4.063 4.906,4.302 0.375,0.24 10 false *3 4.813,2.177 5.188,2.417 0.375,0.24 10 false *a 4.823,4.167 5.198,4.406 0.375,0.24 10 false *a 3.729,3.083 4.104,3.323 0.375,0.24 10 false *b
*A for A25A-FTS *B for M20A-FTS
*1 Suction Hose Sub-assembly *2 No. 2 Air Conditioning Tube and Accessory Assembly
*3 Piping Clamp - -
*a Buckle *b Pull Out




c.

Remove the 2 O-rings from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts with vinyl tape to prevent entry of moisture and foreign matter.



d.

Remove the piping clamp.


Hide 88718Q 3.REMOVE PIPING CLAMP (w/ Sub-cool Accelerator)

a.
E400805C01
1.823,1.771 2.24,1.771 true 0.813,1.417 0.813,1.083 true 1.719,0.552 2.135,0.552 true 0.719,1.438 1.031,1.635 0.313,0.198 10 false *1 2.177,0.479 2.49,0.677 0.313,0.198 10 false *2 1.656,1.688 1.969,1.885 0.313,0.198 10 false *a
*1 Air Conditioning Tube and Accessory Assembly
*2 No. 2 Air Conditioning Tube and Accessory Assembly
*a SST


Install SST to the piping clamp as shown in the illustration.

SST
09870-00025  


b.
E273284C02
2.625,0.74 2.938,0.938 0.313,0.198 10 false *a
*a Push in


Hold the air conditioning tube and accessory assembly and No. 2 air conditioning tube and accessory assembly with each hand and push in SST with both thumbs.

NOTICE:

Do not apply excessive force to the air conditioning tube and accessory assembly or No. 2 air conditioning tube and accessory assembly as they may bend.



c.
E273285C02
1.052,0.271 1.479,0.417 false 0.865,1.719 0.865,1.302 false 0.802,1.74 1.115,1.938 0.313,0.198 10 false *1 0.896,0.177 1.208,0.375 0.313,0.198 10 false *a 2.375,0.854 2.688,1.052 0.313,0.198 10 false *b
*1 Air Conditioning Tube and Accessory Assembly
*a Stopper
*b Pull off


Raise the stopper of SST and remove SST and the piping clamp together from the air conditioning tube and accessory assembly and No. 2 air conditioning tube and accessory assembly.


d.

Remove the piping clamp from SST.


e.

Disconnect the No. 2 air conditioning tube and accessory assembly from the air conditioning tube and accessory assembly.


f.

Remove the 2 O-rings from the No. 2 air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88718N 4.REMOVE PIPING CLAMP (for Air Conditioning Tube and Accessory Assembly Side)