Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
87130D
1.REMOVE BLOWER ASSEMBLY
87201B
2.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Detach the claw and remove the No. 2 air duct sub-assembly.
88897P
3.REMOVE ASPIRATOR
Detach the guide.
Detach the claw and remove the aspirator.
88625Q
4.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Remove the cooler thermistor (room temperature sensor).
88539J
5.REMOVE DRAIN COOLER HOSE
Remove the drain cooler hose.
88539C
6.REMOVE NO. 2 COOLER UNIT DRAIN HOSE (Available as Supply Part)
Perform this procedure only when the No. 2 cooler unit drain hose is available as a supply part.
Remove the No. 2 cooler unit drain hose.
82210K
7.REMOVE AIR CONDITIONING HARNESS ASSEMBLY
Disconnect each connector.
| *A | for LHD | *B | for RHD |
| *C | w/ Driver Seat Centralized Control | *D | w/o Driver Seat Centralized Control |
| *a | Clamp | *b | Guide |
Detach the clamp and guide and remove the air conditioning harness assembly.
87050C
8.REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Remove the 3 screws.
Detach the guide and remove the No. 1 air conditioning radiator damper servo sub-assembly.
87050D
9.REMOVE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
| *A | for LHD |
| *B | for RHD |
Remove the 2 screws.
Detach the guide and remove the No. 2 air conditioning radiator damper servo sub-assembly.
87050E
10.REMOVE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (w/ Driver Seat Centralized Control)
| *A | for LHD |
| *B | for RHD |
Remove the 2 screws.
Detach the guide and remove the No. 3 air conditioning radiator damper servo sub-assembly.
88897M
11.REMOVE HEATER PIPE GROMMET
Remove the heater pipe grommet.
87124B
12.REMOVE HEATER CLAMP
Detach the claw and remove the heater clamp.
87107A
13.REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
|
Remove in this Direction |
Remove the heater radiator unit sub-assembly as shown in the illustration.
Prepare a drain pan or cloth in case the coolant leaks.
88899L
14.REMOVE COOLING UNIT PARTS
| *A | for Type A |
| *B | for Type B |
Remove the cooling unit parts.
88515
15.REMOVE COOLER EXPANSION VALVE
| *A | for Type A |
| *B | for Type B |
Using a 4 mm hexagon socket wrench, remove the 2 hexagon bolts and cooler expansion valve.
Remove the 2 O-rings from the No. 1 cooler evaporator sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88501
16.REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
Remove the 2 screws.
| *a | No. 1 Cooler Thermistor Lead Wire | - | - |
|
Detach lead wire from guide | - | - |
Detach the claw and guide, and then while detaching the lead wire of the No. 1 cooler thermistor from the guide, separate the upper heater case with No. 1 cooler evaporator sub-assembly from the lower heater case as shown in the illustration.
Detach the guide.
| *A | for Type A | *B | for Type B |
Remove the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor from the upper heater case.
88625
17.REMOVE NO. 1 COOLER THERMISTOR
87114B
18.REMOVE HEATER COVER
If the heater cover is removed, the heater cover itself can be reused, but the air conditioning radiator assembly cannot be reused. After the heater cover is installed, the support (triangular rib) on the air conditioning radiator assembly is crushed. Therefore, if the air conditioning radiator assembly is reused, abnormal noise may occur due to looseness.
|
Remove in this Direction |
Remove the screw.
Remove the heater cover as shown in the illustration.