Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for A25A-FXS)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374856 AIR CONDITIONING UNIT(for A25A-FXS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for A25A-FXS)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 87114B 1.INSTALL HEATER COVER

NOTICE:
Perform this procedure only when removal/installation of the heater cover is necessary.

After removing the heater cover, the heater cover itself can be reused, but the air conditioning radiator assembly cannot be reused. After the heater cover is installed, the support (triangular rib) on the air conditioning radiator assembly is crushed. Therefore, if the air conditioning radiator assembly is reused, abnormal noise may occur due to looseness.


a.
E407631C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater cover to a new lower heater case as shown in the illustration.


b.

Install the screw.


Hide 88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.

Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.

E407622C01
0.125,0.104 0.5,0.344 0.375,0.24 12 false *A 3.688,0.104 4.063,0.344 0.375,0.24 12 false *B
*A for Type A *B for Type B



b.

Attach the guide.


c.

While inserting the No. 1 cooler thermistor into the guide, attach the guide and claw as shown in the illustration.

E407623C01
5.76,5.094 6.094,5.094 true 5.594,5 5.771,5.188 0.177,0.188 10 true *a
*a No. 1 Cooler Thermistor Lead Wire - -
V113147

Secure the lead wire between the guide - -



d.

Install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case with the 2 screws.


Hide 88515 4.INSTALL COOLER EXPANSION VALVE

a.

Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and cooler expansion valve.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent


NOTICE:

Do not use any compressor oil other than ND-OIL 11 or equivalent. If any compressor oil other than ND-OIL 11 or equivalent is used, compressor motor insulation performance may decrease, resulting in leakage of electric power.



c.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.
E407620C01
0.135,0.115 0.51,0.354 0.375,0.24 12 false *A 0.135,2.448 0.51,2.688 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Hide 88899L 5.INSTALL COOLING UNIT PARTS

a.
E407619C01
0.125,0.094 0.5,0.333 0.375,0.24 12 false *A 0.125,2.417 0.5,2.656 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Install the cooling unit parts.


Hide 87107A 6.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E407624C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater radiator unit sub-assembly as shown in the illustration.


Hide 87124B 7.INSTALL HEATER CLAMP

a.
E407617

Attach the claw to install the heater clamp.


Hide 88897M 8.INSTALL HEATER PIPE GROMMET

a.
E407625

Install the heater pipe grommet as shown in the illustration.

NOTICE:

Install the heater pipe grommet with the arrow facing up.



Hide 87050E 9.INSTALL NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (w/ Driver Seat Centralized Control)

a.

for LHD:

i.

Attach the No. 3 air conditioning radiator damper servo sub-assembly to the 3 links of the heater case as shown in the illustration.

HINT:

Attach link B to the groove shown in the illustration.


E407626C01
3.208,2.865 3.542,2.865 true 2.188,1.813 2.188,2.146 true 1.74,0.573 1.406,0.573 1.406,0.573 1.406,0.781 true 6,1.771 6.417,1.771 true 1.76,0.469 2.073,0.667 0.313,0.198 10 false *c 2.104,2.125 2.281,2.313 0.177,0.188 10 true *b 3.042,2.76 3.219,2.948 0.177,0.188 10 true *a 6.438,1.677 6.75,1.875 0.313,0.198 10 false *d
*a Link A *b Link B
*c Link C *d Groove




b.

for RHD:

i.

Attach the No. 3 air conditioning radiator damper servo sub-assembly to the 2 links of the heater case as shown in the illustration.

HINT:

Attach link B to the groove shown in the illustration.


E407627C01
2.188,2.156 2.188,1.823 true 5.979,1.802 6.406,1.802 true 3.198,2.875 3.531,2.875 true 3.021,2.771 3.198,2.958 0.177,0.188 10 true *a 2.104,2.146 2.281,2.333 0.177,0.188 10 true *b 6.438,1.708 6.823,2.031 0.385,0.323 10 false *c
*a Link A *b Link B
*c Groove - -




c.
E407615C01
0.125,0.104 0.5,0.344 0.375,0.24 12 false *A 0.125,2.396 0.5,2.635 0.375,0.24 12 false *B
*A for LHD
*B for RHD


Attach the guide.


d.

Install the No. 3 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 87050D 10.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.

Align the gear alignment part of the heater case with the gear alignment part of the No. 2 air conditioning radiator damper servo sub-assembly as shown in the illustration.

E407628C01
1.427,1.469 1.427,1.135 1.427,1.135 1.51,1.135 true 2.688,1.052 2.271,1.052 2.271,1.052 2.271,0.885 true 5.719,2.875 6.052,2.875 6.052,2.875 6.052,2.708 true 0.094,0.104 0.469,0.344 0.375,0.24 12 false *A 3.698,0.104 4.073,0.344 0.375,0.24 12 false *B 2.708,0.969 3.021,1.167 0.313,0.198 10 false *a 1.344,1.458 1.656,1.656 0.313,0.198 10 false *a 5.563,2.771 5.875,2.969 0.313,0.198 10 false *a
*A for LHD *B for RHD
*a Gear Alignment Part - -



b.

Attach the guide.


c.

Install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.


Hide 87050C 11.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.

Align the fitting part and gear alignment part of the heater case with the fitting part and gear alignment part of the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.

E407629C01
4.406,2.656 4.24,2.656 4.24,2.656 4.24,2.323 true 3.177,2.917 3.344,2.917 3.344,2.917 3.344,2.583 true 3.063,2.813 3.24,2.979 0.177,0.167 10 true *a 4.375,2.573 4.552,2.74 0.177,0.167 10 true *a
*a Gear Alignment Part - -



b.
E407613

Attach the guide.


c.

Install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.


Hide 82210K 12.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

Attach the clamp and guide.

E407610C01
0.083,0.083 7.083,2.417 7,2.333 0.083,2.5 7.083,5 7,2.5 0.083,5.083 7.083,7.667 7,2.583 0.177,0.167 0.552,0.406 0.375,0.24 12 false *A 0.177,2.573 0.792,2.823 0.615,0.25 12 false *B, *C 0.177,5.167 0.792,5.417 0.615,0.25 12 false *B, *D 0.927,1.229 1.167,1.417 0.24,0.188 12 true *C 1.76,0.323 2.083,0.531 0.323,0.208 12 true (*C) 1.604,0.333 1.771,0.531 0.167,0.198 10 true *b 2.625,0.823 2.792,1.021 0.167,0.198 10 true *a 2.583,1.354 2.75,1.552 0.167,0.198 10 true *b 2.094,1.719 2.26,1.917 0.167,0.198 10 true *b 4.479,0.74 4.646,0.938 0.167,0.198 10 true *a 4.49,2.135 4.771,2.375 0.281,0.24 10 false *a 4.74,1.479 4.906,1.677 0.167,0.198 10 true *a 5.479,1.115 5.646,1.313 0.167,0.198 10 true *a 5.396,0.479 5.563,0.677 0.167,0.198 10 true *a 5.854,0.448 6.021,0.646 0.167,0.198 10 true *a 2.792,3.469 2.958,3.667 0.167,0.198 10 true *a 1.74,3.021 1.906,3.219 0.167,0.198 10 true *b 2.656,4.198 2.823,4.396 0.167,0.198 10 true *b 2.625,4.552 2.792,4.75 0.167,0.198 10 true *b 5.594,4.656 5.76,4.854 0.167,0.198 10 true *a 5.052,4.5 5.219,4.698 0.167,0.198 10 true *a 4.615,4.563 4.781,4.76 0.167,0.198 10 true *a 4.406,3.844 4.573,4.042 0.167,0.198 10 true *a 4.917,3.896 5.083,4.094 0.167,0.198 10 true *a 5.521,4.094 5.688,4.292 0.167,0.198 10 true *a 5.083,3.177 5.25,3.375 0.167,0.198 10 true *b 5.323,3.521 5.49,3.719 0.167,0.198 10 true *b 5.167,5.802 5.333,6 0.167,0.198 10 true *b 5.396,6.135 5.563,6.333 0.167,0.198 10 true *b 5.635,6.677 5.802,6.875 0.167,0.198 10 true *a 4.99,6.531 5.156,6.729 0.167,0.198 10 true *a 5.688,7.24 5.854,7.438 0.167,0.198 10 true *a 5.167,7.115 5.333,7.313 0.167,0.198 10 true *a 4.688,7.219 4.854,7.417 0.167,0.198 10 true *a 4.479,6.531 4.646,6.729 0.167,0.198 10 true *a 2.615,6.031 2.781,6.229 0.167,0.198 10 true *a 2.448,6.667 2.615,6.865 0.167,0.198 10 true *b 2.458,7.031 2.625,7.229 0.167,0.198 10 true *b 1.552,5.583 1.719,5.781 0.167,0.198 10 true *b 2.781,0.813 3.104,1.021 0.323,0.208 12 true (*C) 2.74,1.344 3.063,1.552 0.323,0.208 12 true (*C)
*A for LHD *B for RHD
*C w/ Driver Seat Centralized Control *D w/o Driver Seat Centralized Control
*a Clamp *b Guide



b.

Connect each connector to install the air conditioning harness assembly.


Hide 88539C 13.INSTALL NO. 2 COOLER UNIT DRAIN HOSE (Available as Supply Part)

HINT:

Perform this procedure only when the No. 2 cooler unit drain hose is available as a supply part.


a.
E417227

Install the No. 2 cooler unit drain hose.


Hide 88539J 14.INSTALL DRAIN COOLER HOSE

a.
E407630C01
1.24,2.604 0.906,2.604 true 1.76,2.615 1.427,2.615 true 1.75,2.51 1.927,2.708 0.177,0.198 10 true *a 0.74,2.521 0.906,2.698 0.167,0.177 10 true *b
*a Hose Notch
*b Rib


Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.

NOTICE:

Do not place the rib on top of the drain cooler hose. Otherwise, water may leak into the interior.



Hide 88625Q 15.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.
E407609

Install the cooler thermistor (room temperature sensor).

NOTICE:

Securely insert it up to the base.



Hide 88897P 16.INSTALL ASPIRATOR

a.
E407608

Attach the claw to install the aspirator.

NOTICE:

Firmly push it down into the heater case until a "click" sound is heard.



b.

Attach the clamp.


Hide 87201B 17.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.
E407607

Attach the claw to install the No. 2 air duct sub-assembly.

NOTICE:
Firmly push it down into the heater case until a "click" sound is heard.

If the claws are not securely pushed in, a gap may form between the heater case and duct, and air leaking from the gap may cause abnormal noise and reduced performance. Also, the audio system may be exposed to cool air, causing it to malfunction.



Hide 87130D 18.INSTALL BLOWER ASSEMBLY