Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0375834 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for HV Model)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the hybrid vehicle control ECU determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the power switch is on (IG) and the dynamic radar cruise control system is operating, the hybrid vehicle control ECU detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

Hybrid vehicle control ECU


Cruise Control

WIRING DIAGRAM

E409640E01
5.365,3.99 6.938,4.365 1.573,0.375 10 false Certification ECU (Smart Key ECU Assembly) 2.76,4 4.813,4.448 2.052,0.448 10 false Skid Control ECU (Brake Booster With Master Cylinder Assembly) 5.354,3.823 5.813,4.021 0.458,0.198 10 false M7 2.76,3.833 3.219,4.031 0.458,0.198 10 false A42 3.313,3.427 3.771,3.625 0.458,0.198 10 false STP2 5.667,3.448 6.125,3.646 0.458,0.198 10 false STP1 3.781,3.365 4.094,3.563 0.313,0.198 10 false 6 5.406,3.354 5.719,3.552 0.313,0.198 10 false 25 2.531,2.583 6.51,2.781 3.979,0.198 10 false Stop Light Switch Assembly 2.656,2.385 3.115,2.583 0.458,0.198 10 false A40 5.198,0.896 5.656,1.094 0.458,0.198 10 false A29 5.208,1.677 5.667,1.875 0.458,0.198 10 false G64 5.198,1.479 5.51,1.677 0.313,0.198 10 false 28*2 5.281,0.677 5.594,0.875 0.313,0.198 10 false 7 5.594,1.583 6.052,1.781 0.458,0.198 10 false ST1- 5.594,0.792 6.052,0.99 0.458,0.198 10 false STP 5.292,2.385 7.052,2.604 1.76,0.219 10 false Hybrid Vehicle Control ECU 3.552,0.896 3.865,1.094 0.313,0.198 10 false L 3.563,1.688 3.875,1.885 0.313,0.198 10 false L 3.021,0.885 3.333,1.083 0.313,0.198 10 false B 3.031,1.51 3.344,1.708 0.313,0.198 10 false B 3.021,2.042 3.333,2.24 0.313,0.198 10 false GND 3.792,0.771 4.104,0.969 0.313,0.198 10 false 3 3.792,1.563 4.104,1.76 0.313,0.198 10 false 5 2.823,0.792 3.135,0.99 0.313,0.198 10 false 7 2.792,1.396 3.104,1.594 0.313,0.198 10 false 6 2.802,1.906 3.115,2.104 0.313,0.198 10 false 2 1.979,1.052 2.594,1.25 0.615,0.198 10 false STOP 1.656,1.698 3.646,1.896 1.99,0.198 10 false ECU-IG2 NO. 3 0.281,0.781 1.25,1.208 0.969,0.427 10 false from Auxiliary Battery 0.271,1.469 1.198,2.031 0.927,0.563 10 false from IG2-NO. 2 Relay 4.792,1.688 5.25,1.885 0.458,0.198 10 false A31 4.76,1.469 5.26,1.802 0.5,0.333 10 false 28*1 0.281,3.396 1.406,3.844 1.125,0.448 10 false *1: for LHD 0.271,3.823 1.396,4.271 1.125,0.448 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A395526C26
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.563,0.344 2.021,0.542 0.458,0.198 10 false A40
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A40-7 (B) - Body ground Power switch off 11 to 14 V
A40-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A40-6 (B) - Body ground Power switch off Below 1 V



d.

Connect the stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A29 and A31*1 or G64*2 hybrid vehicle control ECU connectors.

*1: for LHD

*2: for RHD


b.

Disconnect the A40 stop light switch assembly connector.


c.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the M7 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance for LHD:
Tester Connection Condition Specified Condition
A31-28 (ST1-) - A40-5 (L) Always Below 1 Ω
A29-7 (STP) - A40-3 (L) Always Below 1 Ω
A31-28 (ST1-) or A40-5 (L) - Body ground Always 10 kΩ or higher
A29-7 (STP) or A40-3 (L) - Body ground Always 10 kΩ or higher


Standard Resistance for RHD:
Tester Connection Condition Specified Condition
G64-28 (ST1-) - A40-5 (L) Always Below 1 Ω
A29-7 (STP) - A40-3 (L) Always Below 1 Ω
G64-28 (ST1-) or A40-5 (L) - Body ground Always 10 kΩ or higher
A29-7 (STP) or A40-3 (L) - Body ground Always 10 kΩ or higher



f.

Connect the M7 certification ECU (smart key ECU assembly) connector.


g.

Connect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


h.

Connect the A40 stop light switch assembly connector.


i.

Connect the A29 and A31*1 or G64*2 hybrid vehicle control ECU connectors.

*1: for LHD

*2: for RHD


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR