Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375584 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Missing Message
Detection condition:

Ignition switch ON


Malfunction status:

A communication malfunction with the millimeter wave radar sensor assembly is detected


Malfunction duration:

5 seconds or more


·

Local bus (Open or short)

·

Forward recognition camera

·

Millimeter wave radar sensor assembly


Front Recognition Camera (Front Lighting Control) -

Pattern DTC output part name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera
(Front Recognition Camera(Front Light Control))
U023587

○: DTC is output

-: DTC is not output

Pattern 1 ○ Local bus (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

WIRING DIAGRAM

E384731E10
5.677,0.792 6.292,0.99 0.615,0.198 10 false CANH 5.677,1.448 6.292,1.646 0.615,0.198 10 false CANL 5.427,1.25 6.042,1.448 0.615,0.198 10 false 12 5.458,0.771 6.073,0.969 0.615,0.198 10 false 6 1.229,0.781 1.844,0.979 0.615,0.198 10 false CA1P 1.198,1.438 1.813,1.635 0.615,0.198 10 false CA1N 1.667,1.24 2.281,1.438 0.615,0.198 10 false 6 1.677,0.792 2.292,0.99 0.615,0.198 10 false 5 5.25,1.719 7.146,2.292 1.896,0.573 10 false P8 0.625,1.865 3.125,2.375 2.5,0.51 10 false Millimeter Wave Radar Sensor Assembly 0.615,1.708 2.51,2.281 1.896,0.573 10 false B9 5.26,1.875 7.042,2.229 1.781,0.354 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the millimeter wave radar sensor assembly has been replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.

for Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

for One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN BUS WIRE (FORWARD RECOGNITION CAMERA MAIN WIRE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the P8 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P8-6 (CANH) - P8-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
P8-6 (CANH) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-12 (CANL) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
P8-6 (CANH) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
P8-12 (CANL) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

5.CHECK CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY MAIN WIRE)
2.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Temporarily replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Front Recognition Camera (Front Lighting Control) / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Clear DTCs
50002 433

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Wait 5 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
OK:

DTC U023587 is not output.



Result:
Proceed to
OK
NG



OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY IS DEFECTIVE)

NG

REPLACE FORWARD RECOGNITION CAMERA

5.CHECK CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY MAIN WIRE)
a.

Disconnect the B9 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-5 (CA1P) - B9-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B9-5 (CA1P) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-6 (CA1N) - G114-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B9-5 (CA1P) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B9-6 (CA1N) - G114-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

6.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Temporarily replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CLEAR DTC
7.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Front Recognition Camera (Front Lighting Control) / Clear DTCs.


e.

Clear the DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Clear DTCs
50002 433

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Wait 5 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Front Recognition Camera (Front Lighting Control) / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
50001 433
OK:

DTC U023587 is not output.



Result:
Proceed to
OK
NG



OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY IS DEFECTIVE)

NG

REPLACE FORWARD RECOGNITION CAMERA